Separate the wastewater streams before choosing equipment
A Siliguri data center should select treatment by stream and end use, not use one generic wastewater plant. Characterize evaporative cooling-tower blowdown separately from closed-loop leakage, maintenance drainage, sanitary wastewater and RO concentrate. A reuse-first train normally starts with solids control and UF before RO; the preliminary design envelope is 1,200–6,000 mg/L CTBD TDS, 10–50 mg/L suspended solids and 50–85% standard RO recovery (HydropureWater, 2026). Use ZLD only when the permitted discharge route or freshwater constraint supports it. Because Siliguri-specific flow, source-water, consent and discharge-receptor data were not supplied, final sizing must wait for sampling and permit verification.
The first design decision is whether the cooling architecture actually produces cooling tower blowdown (CTBD). Evaporative and hybrid cooling arrangements can generate a continuous, chemically concentrated purge; closed-loop liquid cooling does not automatically generate CTBD (HydropureWater, 2026). A closed-loop coolant leak is a separate contamination and disposition problem, while sanitary wastewater requires biological and solids treatment rather than inclusion in the cooling-water balance.
Prepare one metered water balance covering makeup, evaporation, blowdown, leakage, maintenance drainage, permeate, concentrate, reclaimed-water demand and final discharge. HydropureWater’s 2026 guidance gives the screening relationship blowdown = 1 ÷ (cycles of concentration − 1). This produces theoretical blowdown of 25% of makeup at four cycles and 20% at six cycles. The same guidance says actual blowdown can exceed that theoretical relationship by 15–30% because of unmeasured losses and emergency dumps (HydropureWater, 2026). Neither relationship establishes treatment capacity at the proposed site.
The data-center stream routing and sizing method provides the workflow to adapt. Do not blend streams merely because they are available; collect representative samples across operating modes, startup, shutdown and maintenance conditions before assigning a treatment route.
| Stream | Primary characterization before design | Provisional route | Approval or acceptance needed |
|---|---|---|---|
| Evaporative or hybrid CTBD | TDS, pH, hardness, silica, TSS, chlorides, sulfate, alkalinity, temperature, cycles of concentration, residual biocides, corrosion inhibitors, antiscalants and dispersants | Solids control, UF, then RO or NF where dissolved-solids removal is required | Cooling designer water balance; feed-specific scaling analysis; reuse specification |
| Closed-loop leakage | Coolant identity, contamination risk, pH, conductivity, metals or glycol where relevant | Segregate pending characterization; no automatic return to cooling service | Cooling-system owner approval and disposal route |
| Maintenance drainage | Floor and equipment wash contaminants, detergents, metals, pH, TDS and TSS | Segregate from CTBD until source control is confirmed | Source owner and environmental consultant sign-off |
| Sanitary wastewater | COD, BOD, TSS, ammonia, pH and pathogen data | Separate biological and solids treatment | Applicable consent and receiving-system route |
| RO concentrate | Full feed chemistry, concentrate TDS, scaling constituents and residual chemicals | Further recovery or separately permitted disposal, subject to site constraints | Discharge route and residue-handling approval |
Choose the end-use route before sizing membranes
Cooling-tower makeup reuse applies when the reclaimed-water specification permits it; HydropureWater’s 2026 research identifies 60–85% recovery for this route and links it directly to freshwater reduction and lower discharge volume. Discharge compliance should not be assumed because the applicable MPCB consent limit for the proposed Siliguri site is not present in the supplied research. ZLD should be reserved for a site where the permitted discharge route or freshwater constraint makes its additional treatment justified.
For reuse, the decision is governed by water quality: can the recovered permeate meet the cooling system’s chemistry, biological and operational requirements without degrading heat transfer or increasing scaling? For discharge compliance, request the consent order and receiving-system limits before sizing the residual treatment train. For ZLD, determine whether a residual liquid discharge is effectively unavailable and whether the freshwater constraint justifies the energy and capital burden.
HydropureWater’s 2026 source describes ZLD at 95–99% overall recovery and identifies evaporative polishing at 15–25 kWh per 1,000 US gallons. It also presents mechanical vapour compression at 95–98% recovery with distillate below 10 mg/L TDS. These figures apply to the cited ZLD configuration; evaporative polishing should be treated as a final stage in a multistep train, not as a substitute for feed characterization and solids control.
Energy must enter the route comparison. Open Engineering’s 2026 preprint found that its wastewater scenario had about twice the global warming potential of the freshwater case, with treatment energy accounting for roughly 80% of the difference (Open Engineering, 2026). A comparison of sewer discharge, reuse and ZLD should therefore compare water savings against treatment energy and chemical use rather than treating recovery as the only metric.
| Decision condition | Treatment route | Evidence-based basis | What must be resolved before sizing |
|---|---|---|---|
| Treated water can meet the cooling makeup specification and reduce freshwater demand | Reuse first | HydropureWater (2026) identifies 60–85% recovery for cooling-tower makeup reuse | Feed chemistry, pilot recovery, reusable-water specification and cooling acceptance criteria |
| A residual discharge route exists with defined consent conditions | Discharge compliance | The decision depends on site-specific limits; no Siliguri MPCB limit is supplied | Consent order, receiving-system capacity, discharge point and residual quality |
| Liquid discharge is effectively unavailable or freshwater alternatives are constrained | High recovery or ZLD | HydropureWater (2026) cites 95–99% overall recovery and 15–25 kWh per 1,000 US gallons for evaporative polishing | Detailed energy balance, power reliability, brine and solids disposal, regulatory route |
| Neither reuse nor discharge has been demonstrated | Keep route open | Open Engineering (2026) shows treatment energy can dominate the environmental difference | Sample streams, test alternatives and obtain the applicable consent review |
Build the UF and RO treatment around CTBD chemistry

The preliminary CTBD design envelope is 1,200–6,000 mg/L TDS with 10–50 mg/L suspended solids, while silica, calcium sulfate, chlorides and residual treatment chemicals can constrain recovery (HydropureWater, 2026). This is a screening envelope, not a substitute for Siliguri feed data. The membrane train should be sized around measured conductivity or TDS, hardness, silica, sulfate, alkalinity, suspended solids and the complete cooling-water chemical programme.
HydropureWater’s 2026 source places a solids-control side stream at 1–5% of circulation flow, with 10–25 micron filtration. UF follows at 90–95% recovery using 0.01–0.1 micron membranes, with chemical cleaning every 1–3 months in the cited design. The hollow-fiber UF pretreatment should therefore remove suspended solids, bacteria, colloids and biological material before RO, while leaving dissolved salts for the next stage.
Standard RO in the cited research rejects 95–99% of dissolved solids and produces 10–50 mg/L permeate TDS at 50–85% recovery and 150–400 psi operating pressure; antiscalant injection is mandatory (HydropureWater, 2026). The industrial RO blowdown treatment must therefore be matched to site chemistry rather than selected from nominal flow alone. The supplier should also demonstrate compatibility with the proposed biocide, corrosion inhibitor, antiscalant and dispersant programme.
Where maximum recovery is required, HydropureWater’s 2026 source describes controlled precipitation of silica, calcium carbonate and calcium sulfate combined with dynamic-mode RO, reaching roughly 95% overall recovery with permeate silica around 1 mg/L. IDE Tech’s 2026 article likewise describes controlled precipitation and dynamic RO for high-recovery CTBD treatment, but this is a more complex chemical route requiring its own solids-handling and operating review. Use the RO design and scaling review to structure that comparison, not to infer Siliguri performance.
| Stage | Published screening basis | Siliguri verification required |
|---|---|---|
| Side-stream solids control | 1–5% of circulation flow; 10–25 micron filtration (HydropureWater, 2026) | Circulation flow, TSS profile, filtration duty and backwash or solids-disposal route |
| UF pretreatment | 0.01–0.1 micron membranes; 90–95% recovery; chemical cleaning every 1–3 months (HydropureWater, 2026) | Feed biology, turbidity, cleaning chemistry and compatibility with cooling chemicals |
| Standard RO | 95–99% dissolved-solids rejection; 10–50 mg/L permeate TDS; 50–85% recovery; 150–400 psi; antiscalant required (HydropureWater, 2026) | Scaling projection, pilot recovery, permeate specification and normalized energy use |
| High-recovery enhancement | Roughly 95% overall recovery with about 1 mg/L permeate silica using controlled precipitation and dynamic-mode RO (HydropureWater, 2026) | Precipitation feasibility, pellet handling, dynamic-operation controls and waste route |
Verify Siliguri site inputs and approval constraints
Final CTBD flow, treatment capacity and discharge limits cannot be fixed without Siliguri-specific operating, chemistry and consent data. The missing information should be assigned to named owners rather than replaced with generic Indian assumptions. This verification step is the difference between a preliminary treatment concept and a design that can withstand technical and regulatory review.
- Cooling designer: provide the cooling architecture, makeup source, operating cycles of concentration, expected blowdown, startup dumps, shutdown discharges, peak cooling demand and emergency routes. Meter each stream identified in the water balance.
- Environmental consultant: obtain representative site samples for conductivity or TDS, pH, hardness, silica, TSS, chlorides, sulfate, alkalinity, temperature, residual biocides, corrosion inhibitors, antiscalants and dispersants.
- Regulatory and civil teams: verify the applicable consent, final discharge route, receiving-system capacity and whether any TDS-bearing discharge is effectively prohibited. The supplied research contains no Siliguri-specific limit, so the discharge-compliance verification workflow should be used only as a process aid, not as the governing consent.
- Utilities and project owner: price freshwater availability, tanker dependence, power tariffs and chemical compatibility. HydropureWater’s 2026 research identifies grid energy as the largest operating-cost swing factor for RO.
Sample CTBD across representative IT loads and operating modes because flow and chemistry change with cooling demand. For sanitary wastewater, collect COD, BOD, TSS, ammonia, pH and pathogen data separately. Closed-loop leakage and maintenance drainage should remain segregated until their contamination and disposal routes are confirmed.
| Required input | Owner | Acceptance before design freeze |
|---|---|---|
| Cooling architecture and metered water balance | Cooling designer and project owner | Peak, normal, startup, shutdown and emergency flows reconciled with makeup and evaporation |
| Feed chemistry across operating modes | Environmental consultant | Signed sampling plan and representative results covering the full test list |
| Reusable-water specification | Cooling designer, operations team and consultant | Written TDS, silica, hardness, chloride, biological, corrosion and operational limits |
| Consent and receiving-system route | Regulatory lead and civil engineer | Applicable consent conditions, discharge point and receiver capacity documented |
| Utility and residue infrastructure | Utilities, civil team and contractor | Power, freshwater, tanker, chemical storage, brine route and solid-waste handling confirmed |
Create a procurement-ready design basis

A supplier guarantee is meaningful only when it is tied to measured feed chemistry and an agreed recovery or reuse specification. Require a feed-specific recovery projection, scaling analysis and pilot recovery data before accepting a quoted recovery for Siliguri CTBD (HydropureWater, 2026). The procurement package should preserve unresolved items as named actions with owners and deadlines rather than silently converting them into design assumptions.
Ask for UF and RO sizing matched to the preliminary CTBD envelope of 1,200–6,000 mg/L TDS and 10–50 mg/L suspended solids, while requiring confirmation against the actual chemical programme (HydropureWater, 2026). Also request membrane-cleaning intervals, redundancy provisions, pilot data, performance criteria tied to measured feed chemistry, and the stated reusable-water specification.
HydropureWater’s 2026 source gives a published 50,000 GPD blowdown-RO benchmark of $250,000–500,000 installed cost and $1.50–3.00 per thousand gallons operating cost. This is a screening comparison from a US-context publication, not a Siliguri quotation. Obtain INR landed cost with duties, freight, civil works, membranes, chemicals, energy assumptions, labour and disposal separately identified. The high-load industrial reuse and discharge decision can help structure commercial comparisons, but local inputs must replace all illustrative assumptions.
Require named delivery and lead-time commitments rather than vague ranges. Each bid should identify the guaranteed feed basis, design flow, recovery definition, permeate quality, test protocol, cleaning method, shutdown scope, spares, redundancy and remedy for demonstrated non-performance.
| Procurement item | Supplier submission required | Buyer acceptance check |
|---|---|---|
| Feed-specific design | Flow basis, feed chemistry, scaling projection and pilot results | Inputs match the Siliguri sampling and cooling design |
| Equipment sizing | UF and RO capacity, recovery definition, redundancy and cleaning intervals | Capacity covers the approved water balance and operating modes |
| Commercial comparison | INR landed cost and operating-cost assumptions separated by category | Published US benchmark is clearly excluded as a local quotation |
| Delivery and acceptance | Named dates, commissioning tests and performance remedy | Dates, test protocol and guarantees are contractually incorporated |
| Approvals and interfaces | Consent assumptions, electrical load, chemical storage, waste routes and utilities | Open approvals have named owners and a closure date before design freeze |
Frequently Asked Questions
What wastewater and cooling blowdown treatment does a data center in Siliguri, India need?
The required treatment depends on the confirmed cooling architecture and stream chemistry. An evaporative or hybrid system may justify a solids-control, UF and RO train for CTBD reuse; closed-loop leakage, maintenance drainage, sanitary wastewater and RO concentrate must remain separately characterized. Final capacity cannot be fixed without Siliguri flow, chemistry and consent data.
When should a Siliguri data center choose UF/RO reuse instead of ZLD?
Choose reuse first when the recovered water can meet the cooling makeup specification and the residual discharge route has defined consent conditions. HydropureWater’s 2026 source identifies 60–85% recovery for cooling-tower makeup reuse. Consider ZLD only after confirming that liquid discharge is effectively unavailable or that the freshwater constraint justifies the added energy and residue-management requirements.
How much will the treatment system cost?
Do not use the published 50,000 GPD blowdown-RO benchmark of $250,000–500,000 installed and $1.50–3.00 per thousand gallons OPEX as a Siliguri price (HydropureWater, 2026). Request an INR quotation separating equipment, duties, freight, civil works, membranes, chemicals, power, labour, replacement and waste handling, based on the verified Siliguri flow and feed chemistry.
How should treatment suppliers be selected and sized?
Shortlist only suppliers that provide feed-specific scaling analysis, pilot recovery data, guaranteed permeate or reuse criteria, cleaning intervals, redundancy details, and named delivery dates. Size the train after the water balance, samples, reusable-water specification and consent review are complete. The final acceptance test should use measured feed chemistry and an agreed performance protocol, not a generic catalogue flow.