Define the wastewater streams before selecting equipment
A Cuautitlan Izcalli data center needs a segregated treatment train for cooling-tower blowdown, process wastewater, glycol-bearing water and sanitary flows—not one generic wastewater system. Blowdown should be characterized for silica, calcium, hardness, suspended solids, organics, metals and biocides because concentrated silica, calcium carbonate and calcium sulfate can obstruct recovery. IDE Tech reports that conventional brackish-water reverse osmosis commonly reaches 75–80% recovery, while higher recovery requires controlled salt precipitation and dynamic RO operation. Local reuse, sewer or discharge requirements must be confirmed with the relevant authorities; the supplied research provides no Cuautitlan Izcalli-specific limits.
Start with a source-by-source mass balance rather than a facility-wide flow estimate. Valicor identifies cooling-tower blowdown, glycol-loop waste, onsite pretreatment requirements, emergency wastewater and maintenance-generated liquid waste as distinct data-center liquid-waste streams. Domestic sewage, fire-water, chiller make-up, cooling-tower make-up and process drains should also be mapped to their origins, destinations and possible reuse constraints.
For each source, record whether discharge is continuous or batch, whether it contains oil, metals, glycol or biocides, and whether cross-contamination would affect reuse. Request source-specific flow measurements across representative operating conditions. IDE Tech’s figure of up to 2 million liters per day applies to a 100-megawatt facility; it is not a design flow for Cuautitlan Izcalli. See the broader data-center cooling-blowdown treatment guidance for the underlying stream-segregation approach.
| Stream or source | Characterization to establish | Procurement implication |
|---|---|---|
| Cooling-tower blowdown | Flow, pH, conductivity, silica, calcium, magnesium, hardness, alkalinity, sulfate, chloride, TSS, organics, metals, residual oxidants and biocides | Sets membrane recovery, antiscalant demand, concentrate volume and reuse limits |
| Cooling-tower and chiller make-up | Supply chemistry, make-up rate and cooling-tower cycles of concentration | Defines the water quality needed for safe reuse |
| Process wastewater and glycol loops | Batch frequency, glycol concentration, oil, metals and treatment compatibility | Usually requires separation or dedicated pretreatment |
| Sanitary, fire-water, maintenance and emergency flows | Generation pattern, contamination risk and available storage | Requires a separate collection, equalization and disposal strategy |
The sampling plan should cover normal operation, maximum blowdown, chemical cleaning, high chemical dosage, start-up and shutdown. Collect source-specific samples rather than relying on one blended sample, because a diluted composite can conceal the silica, hardness or organic peaks that control pretreatment and recovery.
Diagnose the chemistry that limits cooling blowdown recovery
Cooling-tower blowdown is the periodic purge used to control scaling and corrosion after evaporation concentrates dissolved salts in circulating water. It is therefore not a generic brackish stream: its chemistry depends on the makeup water, cycles of concentration, treatment chemicals, tower configuration and operating controls.
IDE Tech describes typical CTBD as enriched with sparingly soluble salts, including silica, calcium carbonate and calcium sulfate. Conventional brackish-water RO is often limited to 75–80% recovery before scaling becomes unmanageable. Pushing beyond that range with conventional designs can require additional stages, booster pumps and recirculation loops, increasing complexity and cost. These figures are reported by IDE Tech in 2026 and should be treated as design context, not a Cuautitlan Izcalli site guarantee.
Calculate the proposed recovery and concentrate-management duty from measured feed chemistry and the required reuse flow. Include the water balance for evaporation, blowdown, product water, reject water and any precipitation or solids separation. If the cooling system may operate at different cycles of concentration, evaluate the complete approved envelope rather than one nominal condition.
The chemical program also matters. Biocides, corrosion inhibitors, antiscalants, residual oxidants and cleaning products can affect membrane compatibility, oxidation demand, precipitation and biological growth. Provide bidders with the chemical inventory, dosing ranges and change-control procedure. Review industrial water-softening equipment only where calcium removal is technically justified; softening does not remove silica and should not be treated as a complete scale-control solution. Equipment and treatment-parts requirements can be incorporated through water-treatment valves and media selection.
A valid scaling projection should use measured silica, calcium, sulfate, alkalinity and conductivity, together with the selected antiscalant and concentration factors. Request the projection method, assumptions, temperature corrections and operating limits. Generic feed analyses are not sufficient for a high-recovery guarantee.
Build a treatment train from characterization to final use

The treatment train should remove source-specific contaminants in sequence, with each stage protecting the next. Start with collection, segregation, equalization and screening so that large solids and oil loads do not determine the capacity of downstream polishing equipment. Equalization is particularly important where glycol drains, cleaning discharges or emergency flows could create short-duration treatment shocks.
- Characterize and segregate. Keep cooling blowdown, glycol-bearing water, process wastewater, sanitary flows and emergency wastewater identifiable through collection and control.
- Equalize and screen. Moderate batch discharges and remove gross debris before fine treatment.
- Remove oil and floatable material where justified. If characterization confirms oil, FOG or floatable solids, evaluate DAF. The HydropureWater DAF system is configured for 4–300 m³/h across 13 standard models for oil, FOG, colloids and suspended solids; applicability still depends on the measured Cuautitlan Izcalli feed.
- Control suspended solids and colloids. Multi-media filtration can protect downstream membranes where the analysis shows particulate or colloidal loading. The DAF selection for oil and suspended solids provides a useful pretreatment check before final equipment sizing.
- Apply membrane pretreatment. Where bacteria, colloids and suspended solids must be controlled before RO, use UF. The HydropureWater UF system uses 0.03-micron PVDF membranes, accepts up to 300 ppm turbidity, includes automatic backwash and air scour, and spans 2,000–40,000 L/h.
- Produce low-salt reuse water. Industrial RO is appropriate where demineralized cooling make-up or another low-salt process feed is required. The industrial reverse osmosis system for cooling-water reuse is specified for recovery rates up to 95% with automated PLC control, subject to the actual feed chemistry and scaling projection.
- Manage the reject stream. Treat RO concentrate, spent pretreatment media and precipitated solids as separate disposal streams until local requirements are confirmed.
Where conventional RO remains constrained by scaling, evaluate a chemistry-controlled process that removes sparingly soluble salts as controlled solids before attempting higher recovery. IDE Tech’s 2026 MAXH₂O description uses controlled precipitation of silica, calcium carbonate and related salts, followed by denser brine handling and dynamic RO operation. This is a specific high-recovery concept, not a drop-in addition to every treatment train.
| Process step | Use it when | Key design input |
|---|---|---|
| Screening and equalization | Flows are variable or batch discharges are present | Peak flow, storage time, upset chemistry |
| DAF | Oil, FOG or floatable suspended solids are confirmed | Oil load, FOG, floatability and solids capture |
| Multi-media filtration | Suspended solids or colloids could compromise membranes | TSS, particle size and filtration rate |
| UF | RO requires controlled colloids, solids and microbial indicators | Feed turbidity, recovery, backwash and integrity testing |
| Industrial RO | Low-salt reuse water or process-quality permeate is required | Scaling projection, recovery, permeate quality and concentrate route |
| Controlled precipitation | Measured scaling chemistry prevents reliable high-recovery RO | Solubility limits, seed solids, solids handling and residual brine |
Decide between reuse, controlled discharge and segregated disposal
The final equipment configuration depends on the required end use, not simply on the lowest apparent treatment cost. Compare four pathways: reuse as cooling make-up, reuse for another permitted process, compliant discharge to a receiving system, or managed off-site disposal. A mixed strategy may be necessary if batch streams cannot meet the reuse specification.
The supplied research does not establish Cuautitlan Izcalli-specific effluent limits, sewer-acceptance criteria, discharge permits or freshwater-stress data. These items must be verified with the competent authority and receiving utility. Foreign or industry-specific limits should not be substituted for a local permit. Obtain written discharge quality, monitoring, reporting and sampling requirements before treating a route as available.
For cooling-tower make-up, define the required conductivity, silica, hardness, alkalinity, chloride, sulfate, suspended solids and microbial indicators. Also obtain the cooling-system supplier’s heat-transfer, corrosion and chemistry limits. Reclaimed water may reduce freshwater demand, but it does not automatically satisfy cooling equipment or environmental requirements.
The energy balance can change the preferred pathway. The 2026 Open Engineering Inc. preprint found that its wastewater-reuse scenario had about twice the global warming potential of the freshwater case, with treatment energy accounting for roughly 80% of the difference. In the same preprint, UF+RO treatment energy increased to more than five times the freshwater case, although improved cooling-tower cycles of concentration reduced blowdown and chemical consumption.
The preprint estimated an indirect water penalty of approximately 0.93 L/m³, less than 0.1% of the direct freshwater-displacement benefit. That result supports the water value of reuse but does not erase the energy and carbon trade-off. Compare recovered water with the actual local supply and environmental context before assigning financial value. Further Mexico-specific decision context is available in the Mexican industrial wastewater treatment case.
| End-use pathway | Required decision | Evidence a buyer must request |
|---|---|---|
| Cooling-tower make-up reuse | Does permeate satisfy cooling chemistry, heat-transfer and corrosion limits? | Cooling-system supplier criteria, water balance and pilot results |
| Other permitted process reuse | Is the receiving process able to accept the proposed water quality? | Process specification and written acceptance criteria |
| Controlled discharge | Does the stream meet the applicable receiving-system and permit limits? | Authority and utility requirements, including monitoring and fees |
| Managed off-site disposal | Which residues are classified and accepted for transport and treatment? | Waste classification, transporter documentation, receiving capacity and pricing |
Set performance guarantees before equipment procurement

Procurement guarantees must refer to the measured feed envelope and the intended end use. Ask bidders to guarantee feed-basis product-water flow, recovery, permeate quality, concentrate quality, equipment availability and cleaning frequency. Define each term: “recovery,” “availability,” “permeate quality” and “cleaning frequency” otherwise leave room for interpretations that do not control operating cost.
| Guarantee or acceptance item | Minimum information required |
|---|---|
| Feed basis | Measured flow and chemistry range, including worst credible blowdown and chemical-cleaning conditions |
| Product water | Flow, recovery and measured quality parameters tied to the reuse specification |
| Concentrate and solids | Flow and chemistry projections, classification assumptions and documented disposal route |
| Availability | Defined exclusions, response times, redundancy and treatment of upstream downtime |
| Controls | Conductivity, pH, differential pressure, flow and ORP where relevant, with protective interlocks |
| Operating costs | Energy, chemicals, membrane replacement, solids handling and operator labor priced separately |
Require a membrane and scaling projection based on measured silica, calcium, sulfate, alkalinity and conductivity. It should state the calculation method, pH, temperature, antiscalant assumptions, recovery basis and cleaning strategy. Where high recovery or an unusual mixed stream is proposed, require pilot or side-stream testing. No Cuautitlan Izcalli site performance data were supplied, so a supplier should not substitute another facility’s result for local verification.
Automatic controls should include conductivity, pH, differential pressure, flow and ORP where relevant, together with interlocks that divert or protect the system when feed quality exceeds the design envelope. Include contingency for membrane fouling, variable cooling-tower cycles of concentration, chemical changes and future server or cooling-capacity changes. Membrane and replacement-element requirements should be defined through RO and UF membrane filter elements, with compatibility and lifecycle cost stated separately.
Evaluate bids over the full operating horizon. A low equipment price can be offset by higher energy use, chemical consumption, cleaning frequency, membrane replacement or concentrate disposal. Conversely, a high-recovery claim has little procurement value unless the supplier guarantees the tested feed basis and identifies the residual-stream route.
Frequently Asked Questions
How should CTBD treatment equipment be sized for a Cuautitlan Izcalli data center?
Size it from measured source flows, seasonal chemistry and required recovery, not facility megawatts alone. Include cooling-tower cycles of concentration, evaporation, batch discharges, product-water demand and concentrate management in the mass balance. Validate the selected flow and chemistry envelope through representative sampling and, where recovery is aggressive, pilot or side-stream testing.
What costs should a buyer include when comparing cooling-blowdown treatment options?
Request separate pricing for energy, chemicals, membrane replacement, media disposal, solids handling and operator labor, offset by the permitted value of freshwater savings. No project-specific cost can be calculated from the supplied evidence because Cuautitlan Izcalli flows, electricity rates, chemical demand, disposal routes and permit conditions were not provided.
Which information should be required when selecting a wastewater-treatment supplier?
Require the source-water dataset, complete water and mass balance, guaranteed permeate and concentrate limits, controls scope, consumables pricing, replacement-part strategy, local service support and performance obligations. Reject a proposal based only on a generic recovery percentage or facility power rating.
Which discharge and reuse limits must be verified for Cuautitlan Izcalli?
Verify the applicable discharge permit, Cuautitlan Izcalli authority requirements and receiving-utility sewer criteria in writing. For reuse, obtain written acceptance criteria from the cooling-system supplier or process user. Do not assume that US, European or industry-specific limits apply at the site.
Related Equipment
- ultrafiltration pretreatment for data-center wastewater — specifications, capacity range, and technical data