Separate the wastewater before selecting equipment
A data center in Nanded generally needs two treatment decisions: one for cooling-tower blowdown and one for sanitary wastewater. Blowdown usually contains concentrated minerals, treatment chemicals and corrosion-related metals, so it needs characterization and either controlled sewer pretreatment or treatment for reuse. The best route depends on the cooling design, blowdown volume and chemistry, local sewer acceptance conditions, water reliability and reuse demand. Nanded-specific limits were not supplied, so no final capacity or compliance claim should be made before obtaining current local rules and site measurements.
Start with the data center wastewater treatment guide and the cooling blowdown treatment guide, but do not combine streams in one treatment train. Cooling-tower blowdown, closed-loop glycol water, cooling condensate and sanitary wastewater have different contaminants, handling requirements and possible destinations. ASCE identifies cooling effluent as the larger share of data-center wastewater, primarily because cooling water cycles through the facility and can concentrate pollutants before discharge (ASCE, March/April 2024).
The cooling architecture changes the water balance. KETOS reports that evaporative cooling typically loses 70–80 percent of withdrawals through evaporation, while a closed-loop system consumes about 5–10 percent and returns approximately 90–95 percent as wastewater available for treatment (KETOS, research excerpt supplied for this article). Record whether each loop is open, closed, hybrid or liquid-cooled, and whether towers operate seasonally or continuously.
| Wastewater stream | Primary risk or contaminant | Provisional route to evaluate | Information required before selection |
|---|---|---|---|
| Cooling-tower blowdown | Concentrated dissolved solids, silica, treatment chemicals and corrosion-related metals | Controlled sewer pretreatment or recovery for make-up reuse | Flow, seasonal chemistry, cooling cycles, sewer conditions and reuse-water specification |
| Closed-loop glycol water | Glycol and potentially contaminated water during drainage or leakage | Containment, leak detection and documented handling; normally not a routine wastewater stream | Glycol type, storage volume, containment, leak response and disposal route |
| Chiller or other cooling condensate | Water quality depends on contamination control and system metallurgy | Possible reuse subject to water-quality and corrosion review | Source, temperature, chemistry, seasonality and piping destination |
| Domestic sanitary wastewater | Organic matter, solids and pathogens | Sanitary sewer or biological treatment where required | Daily and peak domestic flow, local sewer conditions and treatment objectives |
Request current Nanded water-supply reliability, sewer acceptance criteria and discharge-route information before freezing the design. None were established by the supplied research. The feasibility study should document make-up water, evaporation, blowdown, domestic flow, fire-water demand where relevant, and expected expansion load rather than sizing equipment from a generic data-center flow rule.
Test the cooling blowdown before choosing a process
Blowdown treatment cannot be selected from conductivity alone because sewer acceptance, make-up reuse and concentrate handling impose different limits. Build a sampling plan around normal operation and representative peak conditions. For a sewer route, use continuous or logged conductivity and flow measurement so that discharge can be linked to operating changes. The sampling plan should cover the cooling design’s expected operating modes and seasonal conditions, but no Nanded-specific sampling frequency was supplied and must be agreed with the responsible engineer and authorities.
Characterize TDS, conductivity, hardness, alkalinity, silica, chlorides, pH, residual treatment chemicals and relevant metals. HOBI identifies concentrated minerals, biocides, corrosion inhibitors and metals from corrosion as concerns in cooling-tower blowdown (HOBI, research excerpt supplied for this article). These parameters do not all require the same treatment: filtration addresses suspended material, UF addresses colloids and particles, RO addresses dissolved salts, and chemical dosing must have a defined operating purpose.
Also assess the variability of the source and the consequences of reuse. ASCE warns that reclaimed water can increase corrosion, scaling and microbiological growth compared with potable water; it recommends understanding source-water quality through seasonal sampling and considering pH, conductivity, TDS, chlorides, silicon, hardness, alkalinity and microbial counts (ASCE, March/April 2024). The result should be a written treatment objective: sewer compliance, internal make-up reuse, or another approved destination.
| Measured or verified input | Decision supported | Do not assume |
|---|---|---|
| Blowdown flow and conductivity, with logged operating data | Whether a continuous control and monitoring system is justified | That nominal tower data represents actual discharge |
| TDS, silica, hardness, alkalinity, chlorides and pH | Filtration, membrane and scale-control requirements | That low conductivity means low scaling or corrosion risk |
| Residual biocides, corrosion inhibitors and treatment chemicals | Discharge acceptance and reuse compatibility | That all cooling chemicals are compatible with a sewer or reuse route |
| Relevant metals and corrosion indicators | Precipitation, removal and discharge controls | That metal loading is acceptable without local criteria |
| Seasonal and peak operating samples | Treatment operating envelope and storage or equalization needs | That one laboratory sample represents every operating condition |
Use the results to define measurable acceptance conditions. A reuse specification should address the make-up-water quality required by the cooling system, not simply the quality of the membrane permeate. A sewer specification should use the current receiving authority’s acceptance conditions; these were not provided for Nanded, so treatment objectives remain open until confirmed in writing.
Compare sewer pretreatment with blowdown reuse

Sewer pretreatment and blowdown reuse are different procurement decisions, not different equipment packages for the same objective. Sewer disposal requires acceptance by the receiving publicly owned treatment works or other authority before filtration, chemical dosing or disinfection is specified. HOBI notes that local pretreatment programs can set discharge policies for blowdown entering a sewer, and that a large new stream can strain a wastewater plant when salinity or treatment chemicals approach its limits (HOBI, research excerpt supplied for this article).
For reuse, the water balance and cooling chemistry determine whether treatment is technically and operationally justified. A process combining multi-media filtration and UF pretreatment for cooling blowdown reuse can control suspended solids and colloids before an industrial reverse osmosis system. The supplied UF catalogue describes 0.03-micron PVDF membranes, feed turbidity up to 300 ppm, automatic backwash and air scour; those are equipment characteristics, not Nanded-site performance guarantees.
RO is a recovery decision, not a default. IDE Tech reports that conventional brackish-water RO commonly reaches 75–80 percent recovery before scaling becomes unmanageable. The same source describes a MAXH₂O application operating at around 95 percent recovery with permeate silica of about 1 mg/L (IDE Tech, 2026). These values come from different configurations: the high-recovery example is not evidence that a Nanded installation can achieve 95 percent recovery.
| Decision test | Controlled sewer pretreatment | Blowdown treatment for internal reuse |
|---|---|---|
| Primary purpose | Meet confirmed sewer acceptance conditions while controlling discharge volume and pollutants | Recover treated water for cooling make-up while managing concentrate and water-balance effects |
| Precondition | Written receiving-authority criteria, confirmed connection route and flow and chemistry characterization | Confirmed make-up demand, cooling chemistry, recovery target, concentrate destination and operating envelope |
| Typical process elements to assess | Flow control, filtration, pH or chemical adjustment, disinfection and monitoring if required | Filtration, UF where needed, RO where recovery justifies it, controls and concentrate management |
| Main acceptance evidence | Design flow, treatment performance against the applicable sewer conditions, monitoring and waste-route documentation | Permeate or treated-water quality at the agreed recovery, stable flux or pressure performance, controls and concentrate handling |
| Key failure risk | Selecting treatment before local limits or wastewater-plant capacity are known | Assuming high recovery without controlling silica, scale-forming salts and concentrate |
Select chemical dosing only after identifying the required pH, coagulation or scale-control function. An automatic chemical dosing system should operate under defined interlocks and monitoring, not compensate for unidentified compounds or an unstable blowdown composition. Include automatic control, alarms, chemical inventory controls and safe handling in the procurement scope.
Do not call either route feasible until the Nanded discharge route, applicable permit or sewer conditions, signed water balance and measured chemistry confirm it. If sewer acceptance is uncertain, obtain current correspondence from the receiving authority. If reuse is uncertain, first evaluate cooling operation, concentration cycles and the actual demand for recovered make-up water.
Manage sanitary wastewater and residual glycol separately
Sanitary wastewater should remain hydraulically separate from cooling blowdown because it is a biological stream and can contaminate the chemistry used for cooling treatment. Domestic wastewater is normally a relatively limited flow compared with cooling effluent, but it still needs a defined destination and local acceptance conditions (ASCE, March/April 2024). Do not use blowdown equipment as a substitute for sanitary pretreatment without a defined treatment objective and written local requirements.
For closed-loop glycol systems, confirm the glycol type, storage volume, containment, leak detection and maintenance-draining procedure. HOBI states that glycol and water mixtures remain contained during normal operation and that accidental release is the main concern; ethylene glycol and propylene glycol can create high oxygen demand if they reach surface waters, with ethylene glycol also carrying higher toxicity concerns (HOBI, research excerpt supplied for this article). Maintain segregated drainage and a documented response route rather than allowing drained glycol to enter either the cooling blowdown system or sanitary sewer.
Spent glycol from draining, maintenance or decommissioning should be handled through documented, compliant arrangements with qualified waste or recycling partners. This is separate from routine cooling-tower blowdown treatment. Confirm whether the proposed destination accepts the glycol concentration and volume shown in the site’s inventory.
Issue a pre-procurement acceptance checklist

The pre-procurement package should expose missing information before vendors compare equipment. Require a signed data-center water balance covering make-up water, evaporation, blowdown, domestic wastewater and expected expansion. Include the cooling-design description, operating modes, seasonal demand profile and future-load allowance. A vendor should not provide a guaranteed treatment capacity until these inputs are accepted by the purchaser’s engineer.
Require representative laboratory results, blowdown and domestic-flow metering, utility correspondence and the applicable discharge acceptance conditions. Separate confirmed obligations from open assumptions. If the receiving authority has not issued criteria, identify the permit holder, contact and date of correspondence; do not convert an unresolved assumption into a design guarantee.
Use operating opportunities before committing to major treatment expenditure. DOE guidance cited by HOBI states that raising cooling-tower concentration cycles from three to six can reduce make-up water by about 20 percent and blowdown by about 50 percent (HOBI, research excerpt supplied for this article). Evaluate whether controls, instrumentation and cooling-system changes can achieve the intended operating result before sizing recovery equipment.
| Acceptance item | Evidence required before award | Acceptance condition |
|---|---|---|
| Water balance and cooling design | Signed calculations, flow diagrams, seasonal profile and expansion allowance | Design and treated-water flows reconcile with the selected cooling architecture |
| Wastewater characterization | Representative laboratory reports, flow logs and upstream variability review | Parameters and operating envelope match the proposed process and monitoring plan |
| Discharge and reuse authority | Current utility correspondence, sewer conditions, permit basis or written reuse approval | No unresolved local assumption is hidden inside a performance guarantee |
| Equipment performance | Tested flow, treated-water quality, recovery or discharge basis, and operating limits | Guarantees use the same water chemistry and operating conditions as the site design |
| Controls and monitoring | PLC or control narrative, alarms, local and remote monitoring requirements | Automatic responses prevent out-of-limit discharge and identify abnormal chemistry |
| Maintainability | Cleaning access, membrane replacement policy, spare-parts strategy and operator training scope | Maintenance intervals and access are compatible with the facility operating plan |
| Waste and redundancy | Concentrate, sludge and spent-chemical handling plan; utility and equipment redundancy | Residual streams have a documented destination and critical duties have an agreed resilience basis |
| Commercial certainty | Warranty conditions, chemical-compatibility exclusions and agreed operating basis | Water savings are not guaranteed using assumed cycles, flow or chemistry |
For supplier comparisons, request membrane warranty protection, chemical compatibility evidence, redundancy, maintainability and remote monitoring as separate line items. The data center treatment planning guide and the data center wastewater treatment guide can support the feasibility brief, but neither establishes Nanded requirements. The final award should follow utility confirmation and site-specific testing.
Frequently Asked Questions
What should a Nanded data center request when budgeting for wastewater treatment?
Request a quotation based on the signed water balance, measured blowdown and domestic flows, representative chemistry, confirmed discharge or reuse route, equipment redundancy and waste-handling requirements. No Nanded price was supplied, so ask vendors to separate equipment, installation, controls, commissioning, chemicals, membrane replacement, utilities and annual operation. Do not compare quotations based on an assumed blowdown flow.
Which information is needed to select and size blowdown equipment?
Require the cooling architecture, operating profile, flow, conductivity and the measured parameters that affect scaling, corrosion, fouling and discharge. For reuse, also require make-up demand, recovery target and concentrate destination; for sewer discharge, obtain current sewer acceptance conditions. These inputs distinguish pretreatment, UF, RO and disposal sizing.
When should cooling-tower operating changes precede treatment-plant spending?
Evaluate operating changes first when concentration cycles, conductivity control, blowdown routing or metering can materially reduce the flow requiring treatment. DOE guidance cited by HOBI says increasing cycles from three to six can cut make-up water by about 20 percent and blowdown by about 50 percent. Verify the site-specific result through operating data before reducing treatment-plant scope.
How should a supplier be selected for a Nanded feasibility study?
Select against a controlled technical basis: named equipment duties, treatment objectives, measured feed chemistry, utility and permit correspondence, controls, monitoring, maintainability, warranty conditions and residual-waste handling. Require the supplier to state exclusions and warranty assumptions. Do not award on water-savings claims until the agreed operating basis is documented.