Start with the wastewater, not the treatment catalog
Almaty manufacturers generally treat high-COD trade wastewater by matching pretreatment to the contaminant profile, then adding biological or membrane polishing when required. Dissolved air flotation (DAF) is commonly used first for high TSS, FOG and colloidal loads; the supplied Almaty compliance guide states 92–97% TSS removal, 60–80% FOG removal and 50–70% COD reduction. MBR provides tighter separation under well-operated conditions, with stated outlet performance of COD ≤50 mg/L and BOD ≤10 mg/L. Kazakhstan Order No. 168 lists planning targets including COD <150 mg/L, BOD <20 mg/L and total nitrogen <15 mg/L, with 2026 milestones affecting many existing plants. The correct train depends on measured flow, COD/BOD, FOG, metals, pH and the discharge permit—not on COD alone.
Before selecting equipment, record average and peak flow, COD, BOD, TSS, FOG, metals and pH. The 2024 MDPI filtrate study cited by the Almaty industrial wastewater compliance guide reported average COD of 311 mg/L and BOD of 336 mg/L; these values indicate a high-organic Almaty baseline, not a universal design influent. The same guide notes that Kazakhstan practice often establishes maximum permissible discharges case by case through the environmental permit and laboratory schedule. Permit conditions may therefore be stricter or more plant-specific than the Order No. 168 planning values.
Decide whether the plant discharges to sewer or intends direct industrial discharge. Sewer pretreatment usually requires the industrial stream to be protected from solids, oil and acute organic loading, while direct discharge requires the full treatment train to demonstrate the applicable outlet specification. The Almaty industrial wastewater compliance guide provides the local planning benchmark, but the site permit remains the enforceable project basis.
| Design input | Use it to determine | Evidence or required confirmation |
|---|---|---|
| Average and peak flow | Equipment capacity, equalization and bypass provisions | Continuous flow record and production-shift peaks |
| COD and BOD | Biological load and polishing requirement | Laboratory analysis; the 2024 MDPI filtrate baseline was COD 311 mg/L and BOD 336 mg/L |
| TSS and FOG | Whether DAF must precede biological treatment | Measured concentrations rather than plant-wide averages |
| Metals | Whether electrocoagulation or precipitation is required | Species-specific analysis where applicable |
| pH | Coagulant performance, electrode condition and discharge compliance | Native supply water is stated as pH 7.8–8.2 in the Almaty compliance guide |
| Discharge destination | Sewer pretreatment or direct-discharge treatment depth | Environmental permit, sewer operator requirements and Order No. 168 applicability |
Match each contaminant load to the right process
DAF should lead the train when suspended solids, FOG, oil or colloids dominate the pretreatment problem. The Almaty compliance guide states 92–97% TSS removal, 60–80% FOG removal and 50–70% COD reduction across 4–300 m³/h equipment. An industrial DAF wastewater treatment system can therefore protect downstream biological equipment, but its chemical and pH-control scope must be specified with the order.
MBR is the stronger candidate where tight biological separation and a compact installation justify the added complexity. The same guide states COD ≤50 mg/L, BOD ≤10 mg/L and TSS ≤5 mg/L for well-operated trains. For high COD/BOD streams that cannot justify MBR alone, compare DAF followed by biological polishing against a compact integrated MBR wastewater treatment system. The former separates solids and FOG capture from biological polishing; the latter combines biological treatment and membrane separation in a more equipment-intensive configuration.
Electrocoagulation becomes relevant when arsenic, chromium or other metals set the pretreatment requirement. The supplied Almaty guide states 95–99% heavy-metal removal, with COD reduction of 60–80% and TSS reduction of 80–90%. Its stated operating range is approximately pH 6.5–8.5. Because Almaty’s native supply water is pH 7.8–8.2, the process requires acid control or an electrode strategy that prevents passivation. Include the automatic chemical dosing system as a priced process component where pH adjustment is necessary, not as an optional accessory.
| Influent fingerprint | First-stage decision | Further treatment | Stated performance and constraint |
|---|---|---|---|
| High TSS, FOG, oil or colloids | DAF | Biological polishing if required | 92–97% TSS, 60–80% FOG and 50–70% COD; chemical dosing and pH control may be required |
| High COD/BOD with relatively manageable solids | Direct biological treatment or MBR | Verify against permit and Order No. 168 | MBR: COD ≤50 mg/L, BOD ≤10 mg/L and TSS ≤5 mg/L under well-operated conditions |
| High COD/BOD plus substantial TSS or FOG | DAF | Biological treatment; MBR if outlet quality requires it | Compare two-stage DAF plus biology against one integrated MBR train |
| Arsenic, chromium or other metals | Electrocoagulation or precipitation | Further treatment as the permit requires | 95–99% heavy-metal removal; stated COD 60–80% and TSS 80–90% |
- Characterize COD/BOD, TSS, FOG, metals, pH and flow.
- Route suspended solids, FOG or metals to the appropriate pretreatment stage.
- Provide biological polishing where the permit or Order No. 168 requires it.
- Verify the final outlet against the enforceable permit and applicable Order No. 168 parameters.
Design for Almaty pH, altitude and sludge realities

Local conditions can invalidate a process selected only from headline removal rates. The supplied Almaty compliance guide specifies DAF coagulant dosing of 10–30 mg/L PAC plus 0.5–1 mg/L polymer, but states that this regime works only after pH is pulled outside the native 7.8–8.2 band. Acid delivery, metering, calibration and pH interlocks should therefore appear in the base scope.
Almaty’s approximately 850 m elevation reduces oxygen-transfer performance. The guide gives MBR aeration energy of 0.8–1.2 kWh/m³, compared with 0.4–0.6 kWh/m³ for conventional activated sludge, and recommends sizing oxygen transfer toward the upper end of the MBR band. A blower selected from nominal power alone may therefore fail to provide the required biological treatment under site conditions.
Membrane fouling has identifiable operating causes and controls. The supplied guide identifies elevated TSS and under-aeration as common causes of elevated outlet COD, recommends aeration toward 1.2 kWh/m³, and specifies citric-acid cleaning at pH 2–3 about every three months. Daily transmembrane-pressure logging is necessary to distinguish normal resistance growth from a cleaning requirement; the schedule should be adjustable to actual fouling data rather than treated as a universal replacement interval.
Sludge can dominate operating cost. The guide gives disposal rates of ₸2,000–5,000/ton and identifies winter polymer demand, sludge classification and blower power as common cost surprises. Include a filtration and dewatering method, waste classification and haulage rate in the operating model; a plate-frame filter press changes the sludge-water balance and should be evaluated as part of the complete system. Where preliminary solids removal is required, equipment selection should also account for the rotary mechanical bar screen.
Require continuous pH and turbidity monitoring at the DAF float well, plus composite COD sampling at the final outlet. For MBR, require daily transmembrane-pressure records and a clean-in-place chemical kit. These monitoring functions are part of compliance evidence, not optional instrumentation.
Build a 2026 budget around the complete treatment train
Equipment price alone does not represent the capital cost of a compliant treatment plant. The supplied Almaty compliance guide gives CAPEX benchmarks of ₸50–120 million for a 50 m³/h DAF unit, ₸250–300 million for a 200 m³/h MBR train and ₸80–150 million for a 100 m³/h electrocoagulation train. These are equipment benchmarks, not turnkey project prices.
Soft costs must be added explicitly. The guide gives engineering and design at 10–15% of CAPEX, permits at ₸2–5 million, and installation at 15–20%, including civil and electrical works. The project estimate should also show the treatment train, equalization, pumping, chemical storage, dosing, controls, sludge handling, sampling, commissioning and site utilities as separate priced items.
The guide gives total operating cost of ₸15–80/m³ after energy, chemicals, labour and sludge disposal. The result depends on actual flow, electricity tariff, chemical consumption, polymer requirement and sludge classification. A bid that quotes only reagent consumption while excluding acid trim or hazardous-sludge haulage is not comparable with a complete offer.
| Cost element | Supplied Almaty benchmark | Procurement treatment |
|---|---|---|
| 50 m³/h DAF equipment | ₸50–120 million CAPEX | Confirm flow basis, included tanks, pumps, controls and pH-control scope |
| 200 m³/h MBR train | ₸250–300 million CAPEX | Confirm membrane area, aeration design, clean-in-place equipment and replacement strategy |
| 100 m³/h electrocoagulation train | ₸80–150 million CAPEX | Confirm electrode material, acid dosing, power supply and electrode replacement |
| Engineering and design | 10–15% of CAPEX | Show as a separate line |
| Permits | ₸2–5 million | Define permit applications and studies included |
| Installation | 15–20%, including civil and electrical works | Price foundations, piping, power, controls and commissioning |
| Total operating cost | ₸15–80/m³ | Recalculate using site flow, tariffs, chemistry and sludge unit cost |
Normalize every offer to the same influent COD, outlet specification, sludge disposal unit cost and pH-control scope. Omitted acid dosing, polymer make-down, membrane clean-in-place equipment, controls or installation represent deferred capital, not savings. The guide’s worked DAF example—₸70 million CAPEX, ₸5 million annual OPEX and ₸15 million annual avoided fines—produces a stated 4.7-year payback, but it is an illustration rather than a guarantee for an Almaty plant.
Specify the bid so the plant remains compliant after commissioning

Require a written outlet guarantee covering COD, BOD, total nitrogen and every other applicable Order No. 168 parameter, reconciled with the site permit. The planning values cited in the Almaty compliance guide include COD <150 mg/L, BOD <20 mg/L, total nitrogen <15 mg/L and total phosphorus <2 mg/L among 22 parameters, with enforcement deadlines rolling through 2026 for many existing plants. The guarantee must identify test methods, sampling frequency and the influent conditions on which performance is based.
Request a complete scope with acid or alkali dosing, polymer make-down, sludge handling, membrane clean-in-place equipment, controls, sampling and installation shown as priced line items. For DAF selection, use the DAF selection guide for FOG and TSS; for broader process comparison, the high-COD trade wastewater treatment guide provides an additional reference for biological and membrane options.
Make local support contractual. The supplied guide recommends keeping one membrane cleaning cycle and one electrode set on site for the largest cells, and notes that customs lead times for membrane cassettes, electrode plates and PAC totes can extend to weeks. Define response time, spare-parts stock, consumable compatibility and technical support responsibilities in the service agreement.
Require an operating log containing daily flow, weekly COD/BOD, monthly metals where applicable, every cleaning event and every electrode change. This should support monthly self-reporting and the quarterly third-party audits described in the supplied Almaty guide. The 2025 DAF specifications and selection guide is useful for checking the technical completeness of a DAF offer.
Include factory acceptance, site performance testing at agreed influent conditions and a correction protocol for any failed outlet guarantee before final acceptance. Specify who owns sampling, laboratory analysis, calibration, operator training, corrective action and repeat testing. A supplier that guarantees the equipment but leaves permit compliance, sampling or validation responsibilities undefined has not supplied a complete acceptance plan.
Frequently Asked Questions
What is the cheapest practical way to reduce COD in an Almaty food plant?
Start with measured COD/BOD, TSS and FOG rather than assuming DAF alone is sufficient. For FOG- and TSS-heavy food wastewater, the supplied Almaty guide identifies DAF as the usual first stage, with stated COD reduction of 50–70%; biological polishing is added when the sewer route or Order No. 168 outlet requirements demand further treatment. Obtain a bid with flow, influent COD, final outlet and sludge cost stated separately.
When is DAF alone enough, and when is biological or MBR polishing required?
DAF is a pretreatment option for high TSS and FOG, but its stated COD reduction of 50–70% does not demonstrate compliance with the COD <150 mg/L planning target. Biological polishing is required when the remaining organic load cannot meet the applicable outlet specification. MBR is appropriate where the stated COD ≤50 mg/L, BOD ≤10 mg/L and TSS ≤5 mg/L performance is required and the added equipment complexity is justified.
How much does high-COD wastewater treatment cost for a 50 m³/h plant?
For DAF equipment, the supplied guide gives ₸50–120 million CAPEX and approximately ₸15–30/m³ OPEX when sludge haulage is ₸2,000–5,000/ton. A complete project also needs engineering, permits and installation; the guide assigns 10–15% to engineering and design, ₸2–5 million to permits and 15–20% to installation. Request a turnkey quote with flow, influent COD, outlet limits, sludge scope and pH control clearly defined.
Which Almaty conditions should be included in an equipment supplier’s technical offer?
Require native pH conditions, approximately 850 m elevation, sludge disposal cost, aeration demand, local electricity tariff, permit limits, wastewater flow profile and expected contaminant peaks in the offer. For MBR, include aeration sizing and clean-in-place equipment; for DAF and electrocoagulation, include acid dosing, polymer make-down and electrode or sludge handling as applicable.
How should a buyer compare quotations that have different pH-control and sludge scopes?
Normalize bids to the same influent COD, outlet specification, sludge disposal unit rate and pH-control requirement. Treat omitted acid dosing, polymer preparation, membrane cleaning equipment or installation as deferred capital. Also request the operating model for energy, chemicals, labour, sludge classification and consumables so that a lower equipment price is not mistaken for a lower total cost.