Separate the streams before selecting equipment
Cooling blowdown and sanitary wastewater should be separated before a Sevastopol data center selects treatment equipment: the former is the dominant process stream at an evaporatively cooled facility, while sanitary flow follows a separate pathway (HydropureWater, 2026). Blowdown can carry corrosion inhibitors, scale preventers, biocides and metals leached from the cooling loop. Characterization must therefore precede any decision on cycles of concentration or membrane recovery.
Request seasonal source-water minima and maxima rather than relying on a single sample. The quoted analysis associates blowdown with a general TDS screening range of 1,200–6,000 mg/L and links it to scaling, fouling and aquatic-toxicity risks (Genesis Water Tech, 2025, as cited by HydropureWater, 2026). This is a screening range, not a Sevastopol design basis. The procurement package should also identify the cooling configuration, makeup source, chemical inventory, peak blowdown flow, temperature and expected operating schedule.
| Design input | Buyer action | Status for Sevastopol |
|---|---|---|
| Cooling configuration and makeup source | Identify evaporative, hybrid or closed-loop arrangements and water sources. | Site information required |
| Blowdown chemistry | Obtain seasonal pH, TDS, hardness, silica, chloride, metals, residual chlorine and biocide data. | Local sampling required |
| Hydraulic load | Measure peak and average blowdown flow, temperature and operating hours. | Local metering required |
| Sanitary wastewater | Keep separate from the blowdown equipment and permit route. | General guidance |
The broader data-center wastewater and blowdown decision framework can support source-water screening, but it does not establish Sevastopol’s legal requirements. These requirements vary by site, necessitating a direct review of local environmental regulations.
Match each contaminant to a pretreatment step
The pretreatment train should be assigned from measured chemistry, not from a standard package. A general screening range for cooling blowdown is 1,200–6,000 mg/L TDS; the cited analysis associates that range with scaling, fouling and aquatic-toxicity risks (Genesis Water Tech, 2025, as cited by HydropureWater, 2026). The same analysis gives pH 6.0–9.0 as a typical treatment range and approximately 65°C as a discharge temperature target, but both must be confirmed against Sevastopol’s actual permit and receiving system.
Use side-stream or multimedia filtration where suspended solids are material. Use DAF or a lamella clarifier when chemical precipitation creates suspended metals or solids that must be removed before the membranes. Then apply UF to protect RO from particulates, bacteria and higher-molecular-weight organics. The PVDF ultrafiltration pretreatment should be evaluated as part of the complete RO feed-protection envelope, not as a stand-alone guarantee of acceptable blowdown treatment. Pretreatment systems must be sized to handle the specific chemistry identified in the site sampling phase.
| Stage | Selection criterion | Supporting evidence |
|---|---|---|
| Filtration | Required for suspended solids and biological loading. | General process guidance in HydropureWater, 2026 |
| DAF or lamella clarification | Required where precipitated metals, oil or grease removal is necessary. | General process guidance in HydropureWater, 2026 |
| Lamella clarification | Published surface-loading range: 20–40 m/h. | Manufacturer data cited by HydropureWater, 2026 |
| Discharge conditioning | pH 6.0–9.0 and approximately 65°C cited as typical values. | HydropureWater, 2026; local confirmation required |
Chemical compatibility must be checked separately. Permit permission to discharge does not establish that a proposed membrane, seal or lining will tolerate the plant’s actual chemical inventory. If metals removal is required, the clarifier and associated solids-handling equipment must be evaluated as one system; the high-efficiency sedimentation tank is one equipment reference point, not proof that it meets the measured duty.
Choose sewer discharge, partial reuse or ZLD

Partial reuse with a permitted residual discharge is the screening baseline, while sewer-only discharge and zero-liquid discharge remain conditional on local acceptance and concentrate handling. For a cited Kyiv case, the practical baseline was RO polishing plus sewer discharge, with cooling-tower makeup reuse added where useful; that result is not evidence that Sevastopol will accept the same route (HydropureWater, 2026). Selecting an endpoint requires balancing operational costs against local environmental compliance.
The general RO benchmark is 95–99% rejection, permeate TDS of 10–50 mg/L and recovery of 50–85% (Genesis Water Tech, 2025, as cited by HydropureWater, 2026). IDE Tech reports 75–80% as a common practical ceiling for conventional brackish-water RO treating cooling-tower blowdown, because scaling becomes difficult to control beyond that range (IDE Tech, 2026). Select membrane recovery against the measured seasonal envelope rather than the highest catalogue value.
| Route | Select when | Design and permit burden | Evidence status |
|---|---|---|---|
| Sewer discharge | The competent authority confirms that the industrial route is available and the treated stream meets applicable limits. | Equalization, condition-specific pretreatment, discharge monitoring and approved end-of-pipe route. | General evidence; Sevastopol acceptance unverified |
| Partial reuse plus permitted discharge | Treated permeate can satisfy the cooling makeup or another approved use while the residual receives a lawful route. | RO or appropriate polishing, reuse-quality guarantees, residual and concentrate management. | General evidence; local reuse and discharge conditions unverified |
| Zero-liquid discharge | Discharge is prohibited, unavailable or prohibitively constrained and solids can be managed. | RO plus MVC and crystallizer; energy, maintenance and solid-waste handling dominate. | General evidence; Sevastopol case unverified |
For full ZLD, the cited screening envelope is $3–8 million CAPEX, $5–15 per thousand gallons OPEX, 95–99% overall recovery and solid waste below 1% of original blowdown (Genesis Water Tech, 2025, as cited by HydropureWater, 2026). These values are screening figures from the cited source, not a Sevastopol quotation. The industrial RO polishing system should be quoted as one option within the selected route, not as a ZLD package by itself.
Partial reuse reduces freshwater demand but does not authorize the residual discharge. If permeate is returned to cooling makeup, verify the cooling chemistry, concentration limits and continuous demand for the produced water; otherwise, an oversized RO train can create an intermittent reuse flow and a more difficult residual profile.
Resolve the permit and concentrate route early
No supplied research verifies the current Sevastopol industrial-discharge permit, sewer limits, receiving-water rules or reporting cadence. The project therefore cannot claim a compliant discharge route until the competent Sevastopol sewer and environmental authorities provide the controlling documents. This is the principal local verification item in the procurement matrix.
Request the permit text, maximum permissible concentrations, inspection requirements and reporting schedule before finalizing process chemistry. The cited Kyiv analysis recommends involving the sewer authority at concept stage because limits discovered after concept design can force redesign (HydropureWater, 2026). Its warning is general engineering logic, not proof of Sevastopol authority or procedure. Likewise, the cited regional discussion of changed wartime reporting cadences must not be transferred to Sevastopol without written confirmation. Establishing these regulatory parameters early prevents costly design rework.
| Deliverable | Responsible party | Procurement consequence |
|---|---|---|
| Current industrial-discharge rules and permit path | Sevastopol sewer and environmental authorities | Confirms or rejects sewer discharge |
| Applicable maximum permissible concentrations | Authority and design engineer | Defines treatment targets |
| Inspection and reporting cadence | Authority and facility compliance owner | Defines monitoring equipment and operating cost |
| Reuse authorization | Relevant authority and cooling operator | Confirms partial-reuse endpoint |
| Concentrate and solids route | Treatment supplier, operator and waste handler | Determines whether sewer discharge, MVC or crystallization is viable |
Assign a compliance owner from commissioning onward for flow and pH monitoring, sampling ports, laboratory analysis and environmental reporting. Include those responsibilities in the operating cost. The data-center cooling-blowdown treatment guide provides a useful structure for converting permit limits into unit operations, but its Kyiv jurisdiction cannot substitute for Sevastopol confirmation.
Concentrate management must be an endpoint requirement, not an afterthought. RO produces a residual brine even when permeate is reused. Obtain a written route for that residual and, where crystallization is considered, a solids classification, storage, transport and disposal plan.
Turn the route decision into a procurement package

Issue the same design-basis package to every bidder so that treatment quotations remain comparable. Include measured peak and average blowdown flow, cooling configuration, seasonal makeup analysis, blowdown chemistry, treatment chemicals, temperature range, recovery target and required endpoint. Do not substitute total facility water use for actual blowdown flow; the equipment must be sized around the stream being treated.
- Freeze the selected endpoint: sewer discharge, partial reuse plus approved residual discharge, or ZLD.
- Issue the seasonal influent envelope and the current permit limits, with unresolved items clearly marked.
- Require a complete process flow including equalization, pretreatment, RO, reuse, residual handling and utilities.
- Compare guarantees at the complete seasonal feed-water envelope and specified cleaning regime.
Require guarantees for product flow, permeate quality, recovery, normalized energy demand, cleaning frequency and availability rather than nominal capacity alone. Membrane selection should follow the projected feed-water envelope and cleaning regime, not optimistic permeate output (HydropureWater, 2026). Ask suppliers to define chemical storage, dosing, backwash or CIP connections, residual handling, controls, drains and utility requirements. The automatic chemical dosing system should be quoted against the identified chemistry and control strategy, not added as an unconfigured accessory. Detailed procurement specifications ensure that all bidders account for the same operational variables.
For commercial evaluation, separate pretreatment and RO from optional MVC and crystallizer packages. Require each bidder to identify exclusions, replacement costs, concentrate destinations and assumptions that would change the price. This makes the route decision visible in the tender instead of allowing it to disappear into a single equipment total.
Frequently Asked Questions
What flow should be used to size wastewater treatment equipment for a Sevastopol data center?
Use measured peak and average cooling-blowdown flow, not total data-center water use. Provide seasonal operation data and identify whether sanitary wastewater is included in the quoted train. The equipment basis should also state makeup-water chemistry, blowdown temperature and the selected discharge or reuse endpoint.
How should the buyer compare the cost of partial reuse, sewer discharge and ZLD?
Request separate prices for pretreatment and RO, reuse connections, approved residual discharge, MVC and crystallizer, plus energy, chemicals, membrane cleaning, residuals and solid-waste handling. The cited ZLD screening envelope is $3–8 million CAPEX and $5–15 per thousand gallons OPEX (Genesis Water Tech, 2025, as cited by HydropureWater, 2026); this is not a Sevastopol quotation. Require bidders to state exclusions and the assumptions behind each price.
Which supplier guarantees should be required before selecting the treatment train?
Require guarantees tied to the complete seasonal feed-water envelope and the stated endpoint: product flow, permeate quality, recovery, normalized energy demand, cleaning frequency and availability. The supplier must also identify membrane and materials compatibility, backwash or CIP requirements, chemical dosing, controls, residual handling and every utility connection.
What must be confirmed with Sevastopol authorities before the design is frozen?
Obtain written confirmation of the permitted discharge route, applicable concentration and temperature limits, inspection requirements, reporting cadence and any reuse conditions from the competent Sevastopol authorities. The supplied research verifies none of these local requirements, so they remain confirmation items rather than assumed compliance criteria.