Wastewater treatment expert: +86-181-0655-2851 Get Expert Consultation
Engineering Solutions

TSMC Hungary Fab Wastewater Treatment and ETP Guide

TSMC Hungary Fab Wastewater Treatment and ETP Guide

Establish the Hungarian discharge basis before selecting equipment

Wastewater from a TSMC fab expansion in Hungary should be segregated, treated and designed around the stricter applicable Hungarian outfall requirement, rather than a generic semiconductor discharge template. The governing stack includes EU Industrial Emissions Directive 2010/75/EU, the 2024 CWWT BAT conclusions, Act LVII of 2013 on Water Management, Government Decree 1155/2023 implementing the 2022–2027 Danube River Basin Management Plan, and Decree 27/2004 KvVM where the BAT conclusions are silent. Any semiconductor fab discharging more than 10 m³/day falls within the IED threshold described in the supplied research. A county government office, or megyei kormányhivatal, is the permit authority, while NeKI is the national registry. For acquisition or expansion planning, use the TSMC fab ETP engineering guide to structure technical due diligence before equipment selection.

The discharge basis is not a single BAT-AEL value. Under Government Decree 1155/2023, the effective requirement is the stricter of the applicable BAT-AEL range and the RBMP-derived emission-control value; Decree 27/2004 KvVM supplies the default limit where the 2024 CWWT BAT conclusions are silent. This distinction matters when calculating chemical dosing, polishing capacity and monitoring frequency.

Approval layerEngineering meaningProject evidence required
IED 2010/75/EU and 2024 CWWT BAT conclusionsEstablishes BAT-associated emission controls and applicable BAT-AEL ranges.Current permit, applicable annexes, BAT assessment and monitoring basis.
Act LVII of 2013Governs water permits and change-of-operator notification to the county water authority.Site-specific water permit and transfer documentation.
Government Decree 1155/2023Connects the discharge to the 2022–2027 Danube River Basin Management Plan.Receiving-water classification and applicable RBMP-derived control value.
Decree 27/2004 KvVMProvides the default emission limit where the BAT conclusions are silent.Parameter-by-parameter comparison of BAT-AEL, RBMP and KvVM requirements.

Before sizing, the team must obtain the current site-specific permit, receiving-water classification, applicable annexes, technology-specific conditions and any proposed expansion conditions. The permit and treatability evidence should then be translated into a design envelope. Equipment selection cannot substitute for that review.

Separate the wastewater streams that change the ETP design

TSMC’s Alliance for Water Stewardship report shows that fab wastewater is classified by composition and concentration before treatment and reuse through 38 distribution systems. A Hungary semiconductor fab should apply the same segregation logic: a combined wastewater balance cannot reliably size pretreatment, biological polishing or reuse equipment when CMP slurry, FOG, fluoride, metals, TMAH and solvents have different removal routes.

Prepare a water-balance diagram that separately identifies high-solids CMP and FOG streams; fluoride-bearing streams; metal-bearing streams; TMAH and solvent-bearing photoresist streams; ammonia-rich streams; and low-concentration general wastewater. For each stream, record flow, hydraulic variation, pollutant loads, reuse destination, discharge route and treatment objective. The DAF versus clarifier comparison for semiconductor wastewater is useful for defining the solids and FOG pretreatment decision, but neither answer should precede characterization.

TSMC’s 2025 Sustainability Report tracks ten parameters: COD, fluoride, suspended solids, ammonia nitrogen, nitrate nitrogen, arsenic, boron, copper, cobalt and total phosphorus. These form the baseline monitoring list. Add TMAH because many existing Hungarian permits do not cover it, and add PFAS because the EU restriction introduces enforceable obligations from October 2026. Boron is already included in TSMC’s parameter list, but its treatment should remain a separate design duty.

TMAH wastewater should not be carried into a biological block as an untested assumption. The supplied engineering research identifies wet oxidation followed by biological polishing as the emerging baseline, supported by treatability data; the permit addendum should set the applicable emission value. PFAS should also be included in baseline sampling even though it is not equivalent to TSMC’s traditional ten-parameter reporting list.

Hsinchu’s reported water consumption of 150,000 tons per day in 2024, described by Wikipedia in the supplied research as roughly 10% of the city’s water supply, is only a scale indicator. Hungarian hydraulic design must use site-specific process-water demand, wastewater generation, reuse fractions and peak conditions.

Match each pollutant to its treatment duty

Match each pollutant to its treatment duty

The 2024 CWWT BAT conclusion for COD is 75 mg/L as a monthly average where receiving-water flow is at least 10 L/s and 150 mg/L where the flow is smaller. The treatment train therefore needs separate duties for solids and FOG removal, COD reduction, nitrogen control, dissolved inorganic polishing and reuse-water quality; one biological reactor cannot satisfy every parameter.

Clarification or flotation is the logical pretreatment stage for suspended solids and CMP/FOG streams. A DAF system for semiconductor wastewater pretreatment should be evaluated for this solids-separation function. Where reuse quality requires biological polishing and membrane separation, an integrated MBR membrane bioreactor provides the relevant biological and solids-retention function.

Pollutant or dutyApplicable value stated in the researchTreatment function
COD2024 CWWT BAT-AEL: 75 mg/L monthly average at receiving-water flow of at least 10 L/s; 150 mg/L at smaller flows.Source control, biological treatment and polishing as required by the selected BAT route.
Ammonia nitrogen2024 CWWT BAT-AEL range: 0.5–5 mg/L.Nitrification within the biological treatment stage.
Total nitrogen2024 CWWT ceiling: 10–25 mg/L.Anoxic and aerobic biological control, separate from ammonia-nitrogen compliance.
Fluoride2024 CWWT BAT-AEL range: 5–30 mg/L; KvVM default cited as 30 mg/L.Precipitation followed by ion exchange or another approved polishing step.
Boron2024 CWWT BAT-AEL range: 1–5 mg/L.Dedicated polishing duty rather than an assumption that biological treatment achieves compliance.
PFASPFHxA-related phase-in under EU Restriction 2023/707 Annex XVII entry 79 begins on 10 October 2026.Evaluate granular activated carbon, ion exchange and high-pressure reverse osmosis, including reject-stream management.
Arsenic, copper and cobaltIncluded among TSMC’s ten tracked parameters; permit and BAT obligations are parameter-specific.Define separate inorganic removal duties rather than relying on a generic metals claim.

Nitrogen needs two explicit compliance points: the cited ammonia-nitrogen BAT-AEL range of 0.5–5 mg/L is not interchangeable with the 10–25 mg/L total-nitrogen ceiling. Fluoride should move through precipitation and ion exchange or another approved polishing step. Boron requires a dedicated duty because biological treatment performance cannot be assumed. Arsenic, copper and cobalt also need distinct removal concepts supported by site data.

Include PFAS sampling in the first monitoring campaign and evaluate granular activated carbon, ion exchange and high-pressure RO, as identified in the supplied research. The approach must include residual or concentrate management rather than only selecting a removal unit. A UV disinfection system may provide a downstream safeguard against residual low-concentration contamination; it does not replace source control or dissolved-pollutant removal.

Choose between permit transfer, modification and greenfield review

An acquisition or expansion must follow one of three regulatory routes: transfer an existing site-specific permit when the effluent profile already complies, modify the permit when capacity, pollutant envelope or treatment changes materially, or conduct a greenfield IED permit review for a new discharge envelope. The project cannot choose the route solely because the transaction is described as an acquisition; the same BAT-associated analytes will be evaluated at the discharge outfall.

The NeKI pre-transfer notification must be submitted at least 30 days before transfer for an IED installation, regardless of whether the existing water permit transfers. The change-of-operator notification to the county water authority must be filed within 15 days after the legal transfer under Act LVII of 2013. These are separate obligations with different trigger points.

Decision conditionRegulatory pathEngineering evidence
Existing permit and effluent profile remain compliantPermit transfer, with the required pre-transfer and post-transfer notifications.Current permit, compliance records, NeKI pathway and confirmation that capacity and treatment scope do not materially change.
Capacity, pollutant envelope or treatment train changes materiallyPermit modification review.Updated water balance, characterization, proposed treatment train, discharge envelope and reuse assessment.
A new discharge envelope requires reviewGreenfield IED permit review.Full site description, BAT assessment, outfall basis, treatment evidence, monitoring plan and residual-management concept.

Work backward from the closing date and run the registry, permit-review and engineering-evidence workstreams in parallel. The Hungary wastewater permit and change-of-control guide provides the transaction sequence, but the project file should still track each filing, approval and design dependency separately. Before fab ramp, confirm the NeKI registry update and issue the new operator identification code.

Build reuse into the discharge strategy

Build reuse into the discharge strategy

Reclaimed water should be engineered as a permitted discharge and operational-resilience measure, with Hungarian reuse quality derived from process demand rather than copied from an overseas target. TSMC’s 2025 Sustainability Report records an 18% reclaimed-water substitution rate and 23.53 million m³ of cumulative reclaimed-water use. Those figures establish operating experience, not a Hungarian design specification.

Two international precedents illustrate distinct design questions. KTAR reported in September 2025 that TSMC began construction on a 15-acre reclamation plant at its north Phoenix site, designed to raise recycling to as much as 90% through near-zero liquid discharge. That is a site-specific water-scarcity and reuse precedent, not a Hungarian regulatory assumption. The supplied research also reports that the Kaohsiung Qiaotou reclaimed-water plant was contracted to supply 25,500 m³/day to Fab 22 from 2026, with the S.T.S.P. expansion expected to reach 30,000 m³/day by 2028. These are capacity precedents for contracting and scaling decisions.

For Hungary, test reuse against actual process-water demand, effluent variability, water chemistry and the permitted discharge envelope. An RO water purification system may be required to close the gap between reclaimed-water quality and fab-use criteria, but the duty must follow the measured reuse specification.

A materially lower net discharge can strengthen the permit argument; it does not automatically establish a modification. The county water authority determines the route after reviewing the existing permit and proposed treatment and reuse envelope.

Execute the wastewater program in a permit-ready sequence

A permit-ready program begins with characterization and ends with monitored operating evidence; equipment procurement should occur after the permit basis and treatment objectives are established. Use the following sequence for an acquisition or expansion.

  1. Establish the wastewater balance. Commission baseline characterization for the ten TSMC parameters—COD, fluoride, suspended solids, ammonia nitrogen, nitrate nitrogen, arsenic, boron, copper, cobalt and total phosphorus—plus TMAH, PFAS and boron. Verify that stream segregation, reuse destinations and hydraulic peaks remain consistent across source and treatment areas.
  2. Complete pre-permit due diligence. Compare the current site-specific permit with the 2024 CWWT BAT conclusions, applicable RBMP requirement and KvVM default. Record the BAT assessment and the receiving-water basis.
  3. Start the regulatory filing path. File the IED permit review application where required and submit the NeKI pre-transfer notification at least 30 days before transfer.
  4. Close the operator transfer. Submit the Act LVII change-of-operator notification to the county water authority within 15 days after legal transfer.
  5. Confirm registry readiness. Confirm the NeKI registry update and issue the new operator identification code before ramp-up.
  6. Verify operating compliance. Use the first monitoring campaign to verify BAT-AEL compliance, include PFAS sampling, and submit the first IED annual environmental report under the reporting process described in the supplied research.

The final equipment proposal should be checked against site-specific design values, influent testing, hydraulic peaks and permit conditions. Chemical dosing, solids handling and controls must fit the selected treatment sequence rather than remain isolated packages. For solids dewatering and chemical preparation, evaluate a automatic chemical dosing system and plate-frame filter press against measured residuals, sludge characteristics, operating controls and disposal routes.

Frequently Asked Questions

Does transferring an existing Hungarian permit remove the need for BAT-level wastewater compliance?

No. The supplied 2026 research states that the existing site-specific permit can transfer if the effluent profile already falls within the 2024 CWWT BAT-AEL ranges. A change in capacity, pollutant envelope or treatment train materially requires permit review, and the NeKI pre-transfer notification is still due at least 30 days before transfer for an IED installation.

Can DAF or an MBR alone comply with the full semiconductor wastewater permit?

No. DAF or clarification addresses suspended solids and FOG, while MBR provides biological polishing and membrane separation. Neither establishes compliance for fluoride, boron, TMAH or PFAS without additional treatment, controls and permit-specific evidence. The DAF versus clarifier comparison for semiconductor wastewater should be used as a process-selection aid, not a full-compliance argument.

What inputs should a buyer provide when requesting MBR sizing and pricing?

Provide measured average and peak flows, contaminant loads, hydraulic peaks, required effluent quality, reuse targets, available footprint and sludge-handling constraints. A quote based only on headline plant capacity is not defensible for supplier selection because it does not establish membrane area, biological loading, peak equalization or compliance margin. Request a sizing calculation tied to those inputs.

How should an equipment supplier demonstrate PFAS readiness?

Require documented treatment performance, sampling and analytical methods, residual or concentrate management, and a monitoring plan that addresses the PFHxA-related phase-in beginning on 10 October 2026. Also ask how membrane or media compatibility, controls integration, maintainability and permit-relevant performance guarantees will be demonstrated. PFAS readiness should be documented as a treatment train, not presented as a single-unit claim.

References

  1. TSMC Hungary Plant Acquisition: 2026 Wastewater Compliance ...
  2. TSMC Building Water Reclamation Plant
  3. Sustainable Water Management (Alliance for Water Stewardship ...
  4. TSMC breaks ground on water recycling plant
  5. What ETP Does TSMC Need After Expanding Its Fab? 2026 ...

Related Articles

What ETP Does TSMC Need After Expanding Its Fab? 2026 Engineering Guide
Nov 8, 2026

What ETP Does TSMC Need After Expanding Its Fab? 2026 Engineering Guide

TSMC fab expansion wastewater treatment requirements for Arizona, Japan, Germany: regulatory limits…

AI Growth
Contact
Contact Us
Call Us
+86-181-0655-2851
Email Us Get a Quote Contact Us