Start with the factory’s wastewater profile, not a generic COD limit
Isfahan manufacturers generally treat high-COD trade waste with a staged train: characterize and equalize the wastewater, remove FOG and suspended material when present, reduce soluble COD through biological treatment, then polish or disinfect it for reuse or discharge. Iranian evidence shows why biological performance and final compliance must both be checked: the Kermanshah study reported COD reduction from 390–400 mg/L to 40–80 mg/L and 80–92% BOD and COD removal efficiency, but 80 mg/L effluent COD exceeded its cited below-60 mg/L surface-water benchmark. A Tehran study reported COD removal of 89.65–90.97%. The correct system therefore depends on the factory’s waste profile, not COD alone.
The first engineering decision is the destination of the treated water: identify whether it will be discharged to surface water, reused within the factory, or used for another purpose. Then characterize the actual discharge rather than applying a generic industrial-effluent design. Request time-based sampling that covers normal production, cleaning, shutdown and batch dumping. The characterization should quantify flow, COD, BOD5, TSS, oil and grease, pH, nutrients, temperature, and any compounds that may inhibit or resist biological treatment.
A single composite sample can conceal short, high-strength discharges that overload equalization and upset the biological process. Record operating data alongside laboratory results, including production changes, cleaning-chemical use and any off-specification dumps. Domestic sewage is not a valid proxy for trade effluent. The Tehran wastewater study found municipal wastewater to be highly degradable, with an influent BOD5/COD ratio above 0.6, but factory streams may contain FOG, colloids, dyes, solvents, salts or toxic compounds.
| Design input | What the buyer must establish | Why it changes treatment selection |
|---|---|---|
| Flow and discharge timing | Hourly and daily profile, including batch dumps | Determines equalization, pretreatment and biological capacity |
| COD and BOD5 | Time-based concentrations and biodegradability ratio | Separates soluble biodegradable load from resistant or inhibitory material |
| TSS, oil and grease | Suspended-solids and FOG concentrations | Establishes the need for screening and physical pretreatment |
| pH, nutrients, temperature and salts | Operating ranges and inhibitory constituents | Controls biological feasibility, alkalinity demand and season-to-season loading |
| Final destination | Applicable Iranian discharge or reuse requirement and sampling point | Defines the required polishing, disinfection and acceptance tests |
Debris should be excluded before the wastewater reaches pumps or biological equipment. A rotary mechanical bar screen for industrial headworks can protect downstream equipment from rags, plastics, fibers and other solids, but it does not replace characterization of soluble COD or FOG.
Build the treatment train around four removal stages
A complete high-strength wastewater treatment train separates physical protection, flow control, biological COD removal and final solids separation. The normal sequence is industrial pretreatment, equalization, biological COD reduction, solids separation or membrane polishing, and disinfection where required for reuse or discharge.
First, remove debris at the plant inlet. Screening protects pumps, aeration equipment and membranes from materials that should not enter the process train. Second, balance flow and load in an equalization tank. This step should absorb normal production variation and controlled batch discharges rather than allow each release to pass directly to biological treatment.
Third, use physical pretreatment where characterization identifies suspended solids, colloidal material, oil and grease or FOG. The industrial DAF pretreatment system has a catalog flow range of 4–300 m³/h and is intended for industrial pretreatment. DAF can remove the floatable and settleable material that would otherwise interfere with aeration, sludge handling or membrane operation; it is not the principal biological COD-removal stage. The DAF selection guide for FOG and TSS sets out the application questions that should precede equipment selection.
Fourth, reduce biodegradable dissolved and particulate organics biologically. Where the reuse objective requires membrane-based solids separation and a smaller treatment footprint, use an integrated MBR wastewater treatment system. Membrane separation then clarifies the biologically treated water, with disinfection added only where required by the intended reuse or discharge route.
| Stage | Primary function | Design basis | Key failure if omitted |
|---|---|---|---|
| Screening | Remove rags, plastics, fibers and debris | Debris characteristics and flow | Damage to pumps, aerators and membranes |
| Equalization | Balance flow, concentration and batch discharges | Hourly flow and load profile | Shock loading and variable treatment performance |
| DAF or other pretreatment | Remove FOG, oil, colloids and suspended solids where needed | Oil-and-grease and TSS data | Interference with biological treatment or membrane fouling |
| Biological treatment | Oxidize biodegradable organics | COD, BOD5, temperature, pH, alkalinity and toxicity | Residual COD and unstable sludge separation |
| MBR or solids separation | Separate biological solids and produce clarified effluent | Reuse objective, effluent target and membrane design data | TSS carryover and failure to meet the intended reuse condition |
The Kermanshah evidence demonstrates why the train cannot end at average removal efficiency. That study reported raw COD of 390–400 mg/L and effluent COD of 40–80 mg/L, but the 80 mg/L result remained above its cited below-60 mg/L surface-water benchmark.
Use activated sludge as the benchmark for biodegradable COD

Activated sludge uses microorganisms to oxidize biodegradable organics, so the process is governed by biological oxygen demand, sludge settleability, temperature and contaminant toxicity rather than COD alone. The Kermanshah study estimated 80–92% BOD and COD removal efficiency at the wastewater treatment plant. It also reported BOD decreasing from 125–200 mg/L in raw sewage to 15 mg/L in the effluent.
That performance is a municipal reference, not a guarantee for an Isfahan factory. Tehran municipal wastewater was characterized as highly biodegradable, but industrial effluent may include intermittent FOG, salts, dyes, solvents or inhibitory cleaning chemicals. These constituents can change oxygen demand, settleability and microbial viability without appearing in a routine COD result.
Local process evaluation is also changing. A 2025 activated-sludge greenhouse-gas modeling study for the Isfahan wastewater treatment plant, published by Shiran, Nabi Bidhendi and Mehrdadi in the Journal of Advances in Environmental Health Research, shows that biological plants are now evaluated not only for pollutant removal but also for process and operating emissions. Any activated-sludge proposal should therefore state whether aeration, sludge handling and energy-related emissions are included in its operating-cost and environmental comparison.
For vendor design or pilot testing, request dissolved oxygen, mixed-liquor solids, sludge age, temperature, alkalinity and contaminant feed data. These inputs allow the supplier to establish an oxygen and solids balance rather than select a reactor from flow and COD alone. The anaerobic MBR guide for high-strength wastewater is relevant when the waste profile supports recovery of soluble biodegradable COD, but its applicability still depends on the factory characterization.
The acceptance criterion should be tied to the final effluent requirement and verified during representative loading. A high average COD removal efficiency cannot compensate for a single batch that exceeds the applicable limit or disrupts biological treatment.
Choose DAF, MBR or a combined train by application
DAF, MBR and a combined train solve different problems, and the decision follows the waste characterization. DAF is the pretreatment choice when oil, FOG, suspended solids or colloids must be removed before biological treatment; the catalog range is 4–300 m³/h. MBR combines biological treatment with membrane solids separation when the reuse objective requires membrane-based clarification and a smaller treatment footprint; the catalog capacity is 10–2,000 m³/day with sub-1 μm filtration. Neither module removes prohibited contaminants or compensates for inadequate source control.
A combined DAF–MBR train is appropriate when FOG and solids could impair biological treatment or membrane performance and the final water has a reuse objective. If the waste is highly biodegradable and relatively free of floatable oils, adding DAF may add equipment, chemical demand and sludge handling without a corresponding treatment objective. The high-COD trade-waste treatment roadmap provides a useful process-ordering reference, but Isfahan suppliers must base the final design on the factory’s own measurements.
| Decision | Use DAF when | Use MBR when | Use DAF–MBR when |
|---|---|---|---|
| Primary need | Remove oil, FOG, colloids or suspended solids before biology | Provide biological treatment and membrane separation | Protect biological and membrane stages from the characterized contaminants |
| Catalog capacity | 4–300 m³/h | 10–2,000 m³/day | Each module sized against the same flow and load basis |
| Effluent role | Prepared influent for downstream biological treatment | Membrane-separated final effluent for the specified reuse route | Protected biology followed by membrane-based solids separation |
| Main limitation | Not the principal biological COD-removal stage | Does not replace source control or remove prohibited contaminants | Requires treatment of FOG, solids, fouling and chemical consumption in the combined scope |
Chemical dosing should follow the characterization rather than become a default package. Coagulants, flocculants or pH-adjustment chemicals may be needed for DAF solids capture, equalization pH control or biological alkalinity. An automatic PLC-controlled dosing system should define the actual chemical, dose range, control loop, storage requirement and operator intervention. The automatic chemical dosing system should therefore be specified around the control objective, not sold as an unqualified guarantee.
The Tehran study reported municipal removal efficiencies of 89.65–90.97% for COD, 92.11–93.41% for BOD5 and 91.48–93.18% for TSS. These are useful municipal reference results, but they are not industrial performance guarantees or a substitute for site acceptance testing.
Turn the effluent target into a commissioning and compliance plan

The procurement specification must name the final effluent target and sampling point before equipment is ordered. A reuse requirement is not equivalent to a surface-water discharge requirement: the intended reuse determines whether additional solids separation, nutrient control, disinfection or additional treatment is necessary. The applicable Iranian requirement must also be confirmed for the actual receiving water and reuse route.
The Kermanshah study compared treated effluent with Environmental Protection Organization of Iran benchmarks cited by the authors: COD below 60 mg/L, BOD below 30 mg/L and a 40 mg/L threshold for most suspended solids in treated waters. These are reference points for the discussion, not a substitute for confirming the current legal requirement applying to the factory in 2026.
Seasonal variation makes the acceptance plan especially important. The study reported effluent COD of 40 mg/L in April, within its cited below-60 mg/L benchmark, but 80 mg/L in July, outside it. The same study reported effluent BOD of 15 mg/L and TSS of 20–25 mg/L, compared with raw sewage values of 125–200 mg/L BOD and 110–140 mg/L TSS.
Commissioning should monitor influent and effluent while verifying the flow balance, biological stability and solids separation. Test the treated water against the actual reuse application rather than relying on a generic permeate-quality statement. For reuse, the Tehran study observed that treated wastewater in Iran is commonly reused after freshwater blending; the proposed treatment objective should identify whether that practice applies to the factory and who controls the blend.
Untreated trade-waste bypasses, equalization overflow and uncontrolled batch discharges must be treated as compliance risks. Require high-level alarms, interlocks and documented operating procedures. Permit the full wastewater stream to reach the treatment plant without complete isolation or uncontrolled dilution.
Specify equipment and suppliers before asking for a price
Comparable quotations begin with one controlled process basis, not a request for a generic high-COD package. That basis should include the wastewater characterization, hourly and daily flow profile, final discharge or reuse target, site constraints, available utilities, automation requirements and future expansion plan. A supplier that quotes from COD and average flow alone has not received enough information to guarantee performance.
Ask every supplier to state its treatment objectives, design flow, performance guarantees, pretreatment requirements, chemical consumption, sludge-production estimate, control philosophy, commissioning tests and included engineering services. Require confirmation that the proposed DAF or MBR equipment addresses the factory’s actual FOG, suspended-solids, COD and flow profile rather than adapting a municipal package design.
The exclusions should be explicit. Identify whether the quotation includes civil works, chemical supply, sludge disposal, membrane replacement, power connection, commissioning and operator training. These items affect both capital cost and lifecycle operating cost, and leaving them ambiguous makes quotations unsuitable for comparison.
Supplier assessment should also cover local site execution, spare-parts availability, membrane sourcing, operator capability and technical support. The DAF-versus-clarifier wastewater comparison is relevant to equipment evaluation because pretreatment selection must follow the contaminant objective rather than a generic preference for one clarification method.
The supplied research does not establish a universal equipment price for Isfahan. A defensible budget requires quotations against the same process basis, with capacities, guarantees, utilities, chemicals, sludge handling, civil works, controls and commissioning services separated. No factory should compare a pretreatment price with a complete biological treatment price without reconciling the scope.
Frequently Asked Questions
What inputs should an Isfahan factory provide before requesting a high-COD treatment price?
Provide the time-based flow, COD, BOD5, TSS, oil and grease, pH, nutrients, temperature and toxicity profile; the reuse or discharge destination; site utilities and constraints; and the required final effluent specification. These inputs determine whether pretreatment, equalization, biological treatment and polishing are required and allow quotations to be compared.
Does a pretreatment quotation cover the same scope as a complete high-COD treatment quotation?
No. A DAF quotation primarily covers physical pretreatment, while a complete train must also address screening, equalization, biological COD reduction, solids separation, controls, sludge handling and any disinfection. Request a scope matrix that identifies included equipment, guarantees, civil works, chemicals, utilities, commissioning, training and exclusions.
Why should seasonal and batch conditions appear in the sizing and performance guarantee?
The Kermanshah study recorded effluent COD of 40 mg/L in April but 80 mg/L in July against its cited below-60 mg/L benchmark. The equipment basis should therefore include normal production, cleaning and batch-discharge conditions, with representative influent loading during commissioning rather than relying on one favorable sample.
How should a supplier be qualified for treated wastewater reuse or discharge?
Require the supplier to identify the intended reuse route, applicable effluent requirement, sampling point, design flow, pretreatment needs, chemical and sludge outputs, control philosophy and acceptance tests. Confirm membrane availability, spare parts, operator capability and local technical support; the Tehran study notes that reuse in Iran commonly includes freshwater blending, so the treatment objective must state whether blending is part of the project.