What DAF capacity can be confirmed for the Texas plant?
A specific DAF capacity for Hyundai’s new Texas auto plant cannot be confirmed from the supplied information because the plant’s wastewater flow, TSS, FOG, peak profile and discharge target are not stated. Size the DAF from the 85th-percentile design flow, normally using 4 gpm/ft² within HydropureWater’s 3–5 gpm/ft² hydraulic-loading band. At 200 gpm, the published example requires 50 ft², a 60 gpm recycle pump at 80 psig and 15–20 minutes of flocculation. Final capacity must also satisfy the 0.005–0.060 lb air/lb TSS and 20–50% recycle criteria.
That numerical example is a sizing demonstration, not a Hyundai plant requirement. The supplied research contains no verified design flow, TSS concentration, FOG level, peak-flow profile or permit limit for the Texas automotive facility. A defensible procurement document therefore has to state those missing inputs and require bidders to reproduce the same calculations from the same verified data.
DAF capacity also has a different meaning from catalogue throughput. As HydropureWater’s 2026 DAF engineering specifications explain, a tank may pass 300 gpm of clean water without being able to clarify 300 gpm of contaminated wastewater while meeting the discharge TSS target. The meaningful capacity is the flow that the unit can treat while the hydraulic loading, air-to-solids ratio, retention time and recycle rate remain within their operating envelopes.
Until the plant provides its design-flow and influent data, the defensible answer is a calculation and RFQ basis—not an unsupported equipment-capacity claim. The buyer should not convert automotive production output directly into wastewater flow or accept a nominal flow rating without contaminant-loading and hydraulic cross-checks.
Plant data required before ordering a DAF
The design basis must describe both continuous wastewater production and the short-duration events that can destabilize clarification. HydropureWater’s 2026 sizing guide calls for the 85th-percentile daily wastewater flow, with brief excursions above the hydraulic-loading limit acceptable. For an automotive plant, that basis must separately identify continuous process wastewater, batch-intensive wash-water discharge and any other variable stream that can reach the DAF.
Request a monitored flow record and a field-characterization program covering the production cycle. A single average flow can conceal the peak that determines surface area, recycle-pump duty and equalization requirements. The characterization should also establish whether stormwater, nondestructive-test leakage, cooling water or production-expansion flows are segregated from the wastewater sent to pretreatment.
Chemical treatment is part of the data request, not an accessory. HydropureWater’s 2026 guide identifies coagulation and flocculation chemistry as a major influence on the required air-to-solids ratio. A buyer should therefore provide information about existing treatment, proposed polymer or coagulant use and any sampling results that show how the stream responds to conditioning. This also supports the automatic chemical dosing skid review.
| RFQ input | Information required | Why it affects the DAF specification |
|---|---|---|
| Design flow | 85th-percentile daily flow and short-duration peak flow | Sets surface area, equalization and pump duty |
| Flow pattern | Continuous flow, batch wash-water discharge and variable-stream segregation | Distinguishes sustained duty from transient loading |
| Solids and oils | TSS, FOG, oil and grease, including sampling method | Determines solids loading, floatable contaminant load and standard-envelope applicability |
| Process chemistry | pH, temperature and existing or proposed chemical conditioning | Influences floc development and required air-to-solids ratio |
| Treatment objective | Applicable discharge or sewer pre-treatment limit | Defines the performance criterion that catalogue throughput cannot establish |
| Future basis | Production expansion and likely changes in wastewater composition | Prevents immediate under-sizing after expansion |
Use field measurements to establish the wastewater profile rather than assuming a production-rate relationship. The supplied evidence does not provide a conversion from vehicle production to wastewater flow, and no such conversion should be embedded in the RFQ without project-specific data.
Calculate DAF surface area from design flow

The hydraulic area calculation is straightforward: divide the verified design flow by the selected hydraulic loading rate. HydropureWater’s 2026 sizing guide identifies 3–5 gpm/ft² as the normal industrial operating band and 4 gpm/ft² as the typical design point, with the 85th-percentile daily flow used for design.
Required surface area = design flow in gpm ÷ hydraulic loading rate in gpm/ft².
Using the guide’s published example, 200 gpm divided by 4 gpm/ft² produces a required area of 50 ft². The same flow converts to approximately 45 m³/h, placing it in HydropureWater’s 20–80 m³/h mid-class bracket. This calculation establishes hydraulic area only; it does not establish TSS loading, air demand, retention time or recycle-pump capacity.
Operating below 3 gpm/ft² can increase capital cost and reduce cross-flow velocity toward the 2 ft/s settling threshold identified in HydropureWater’s 2026 guide. Operating above 6 gpm/ft² can shear floc at the inlet and shorten bubble-contact time, allowing fines to escape. The selected rate should therefore be supported by wastewater characteristics rather than selected merely to minimize surface area.
| Calculation item | Published basis | Procurement meaning |
|---|---|---|
| Hydraulic loading band | 3–5 gpm/ft² | Normal industrial operating range |
| Typical design point | 4 gpm/ft² | Illustrative basis for the sizing calculation |
| Published example | 200 gpm ÷ 4 gpm/ft² = 50 ft² | Calculated clarification area, not a plant-specific rating |
| Example flow conversion | 200 gpm ≈ 45 m³/h | Falls in the 20–80 m³/h mid-class bracket |
| Standard catalogue envelope | 4–300 m³/h across 13 models | Supports comparison with the industrial DAF system |
| Above the catalogue envelope | More than 300 m³/h | Compare parallel trains with a balanced inlet manifold against custom fabrication |
If the verified duty exceeds 300 m³/h, parallel standard trains are credible only when the inlet manifold can distribute flow evenly. Otherwise, a custom rectangular tank may provide a more controllable arrangement. The final configuration must remain inside the same hydraulic and contaminant-loading basis rather than treating catalogue boundaries as automatic approval.
Check solids loading, retention and recycle performance
Hydraulic area alone cannot establish a valid DAF specification because the air-to-solids ratio, retention time and recycle system operate as a coupled system. HydropureWater’s 2026 guide gives an air-to-solids range of 0.005–0.060 lb air per lb TSS, retention of 10–30 minutes and recycle of 20–50% of influent flow.
Calculate the TSS mass load from the verified flow and concentration, then calculate the dissolved-air delivery from the proposed recycle flow and pressure. The result must fall inside the stated air-to-solids band. Well-dosed floc may support an air-to-solids ratio toward 0.005–0.010, while dispersed colloids may require a ratio toward 0.040–0.060; HydropureWater’s 2026 guide treats chemistry as the reason these values differ.
Check the saturator against the typical 60–80 psig operating range and the proposed bubble size against the 10–100 µm design window. Confirm how the white-water system distributes bubbles through the contact zone. Retention must include the effective residence supplied by an upstream floc tube or reaction tank, not merely the nominal volume of the flotation tank.
| Performance check | Published criterion | Acceptance evidence required |
|---|---|---|
| Air-to-solids ratio | 0.005–0.060 lb air/lb TSS | Air-delivery calculation tied to TSS mass loading and chemistry |
| Effective retention | 10–30 minutes | Floc-tube and reaction-tank residence included |
| Recycle ratio | 20–50% of influent flow | Recycle-pump curve at calculated gpm |
| Saturator pressure | Typically 60–80 psig | Duty point, pump performance and summer-temperature review |
| Bubble size | 10–100 µm design window | Proposed white-water and contact-zone arrangement |
| Example consistency check | 200 gpm with 60 gpm recycle at 80 psig and 15–20 minutes of flocculation | Vendor demonstration that pump and conditioning support the calculated duty |
The 200 gpm example is useful as a consistency check because the specified 60 gpm recycle at 80 psig and 15–20-minute floc tube fit the guide’s other operating criteria. It must not be transferred to Hyundai without verified flow and contaminant data. The DAF selection guide for FOG and TSS also limits the standard catalogue assumptions to TSS no greater than 1,000 mg/L and FOG no greater than 500 mg/L without vendor review.
For waste above 2,000 mg/L TSS, HydropureWater’s 2026 guide calls for a 20–30% hydraulic-loading safety margin and a target of approximately 2.5–3.5 gpm/ft². That adjustment must be reflected in the calculated area and recycle duty; it cannot be added later without changing the equipment basis.
Match automotive wastewater risk to equipment configuration

Oil, FOG, suspended solids and colloids must be treated as separate automotive wastewater constraints. A dissolved air flotation system can remove floatable oil, FOG, suspended solids and conditioned colloidal material, but its performance depends on upstream coagulation and flocculation. The equipment configuration should therefore follow the characterized wastewater profile—not a general assumption that all automotive wastewater will respond in the same way.
HydropureWater’s 2026 guide distinguishes well-dosed floc, which can operate toward an air-to-solids ratio of 0.005–0.010, from dispersed colloids that may require 0.040–0.060. Chemical selection, mixing energy, flocculation time and recycle performance must be coordinated rather than specified independently.
| Project condition | Configuration decision | Principal engineering check |
|---|---|---|
| Calculated duty within 4–300 m³/h and influent inside the catalogue envelope | Compare standard catalogue DAF configurations | Surface area, TSS loading, air supply and recycle duty |
| Calculated duty above 300 m³/h with well-characterized flow | Compare parallel catalogue trains | Balanced inlet manifold, equal train loading and independent equipment packages |
| Variable influent, single scraper requirement or unsuitable skid arrangement | Compare custom rectangular fabrication | Hydraulic distribution, float-layer control and site arrangement |
| Floatable oil, FOG, TSS or colloidal loading requiring conditioning | Include chemical conditioning and controlled recycle distribution | Floc quality, air-to-solids ratio and white-water arrangement |
The 92–97% TSS removal cited in HydropureWater’s 2026 guide is a performance target for properly conditioned influent. It is not evidence that Hyundai’s plant will achieve that range, and it cannot substitute for a discharge-limit calculation. Likewise, the DAF versus clarifier comparison for auto plants should inform technology selection, but the final choice still requires project-specific wastewater data.
For an automotive facility, include automatic chemical dosing, balanced recycle distribution and upset-flow management in the equipment comparison. Comparing tank flow ratings alone omits the variables most likely to determine actual clarification performance.
Turn the calculation into a defensible supplier specification
A comparable bid should show the calculation behind every capacity claim. HydropureWater’s 2026 guide identifies reproduction of the full sizing arithmetic from the same influent data as the fastest way to validate an engineered specification. A bidder that supplies only a nominal gpm rating has not demonstrated that the unit can meet the treatment objective.
Require each supplier to identify design flow, selected hydraulic loading, calculated surface area, TSS loading, air-to-solids ratio, retention time, recycle flow, recycle pressure and bubble-size range. Each proposal should also show whether the offer is one standard unit, multiple parallel trains or a custom tank, and identify any duty outside the 4–300 m³/h catalogue envelope.
| Bid item | Required calculation or disclosure | Review question |
|---|---|---|
| Hydraulic basis | Design flow, loading rate and surface area | Does the area reproduce from the same project flow? |
| Solids basis | TSS concentration and mass loading | Is the result outside the standard contaminant envelope? |
| Air system | Air-to-solids ratio, recycle flow, pressure and bubble range | Does the recycle pump meet the calculated gpm at the stated duty? |
| Hydraulic retention | Total effective retention, including flocculation | Is the stated time supported by the actual vessel configuration? |
| Configuration | Standard, parallel train or custom tank | How is flow balanced across trains and treatment stages? |
| Seasonal review | Summer-temperature and saturator-pump considerations | What derating, if any, is included in the final duty? |
Verify the recycle pump against the calculated flow rather than accepting tank volume as proof of capacity. An undersized pump can reduce air delivery and undermine removal even when the flotation tank dimensions are correct. Require the pump curve, operating point and proposed control limits. Also request the supplier’s summer-temperature review and any saturator-pump derating before accepting the bid.
The final purchase specification should reconcile hydraulic area, contaminant loading, air delivery, retention and recycle performance in one calculation. That gives procurement a technical basis for comparing standard equipment, parallel trains and custom fabrication without inventing a Hyundai-specific capacity.
Frequently Asked Questions
What DAF capacity is required for Hyundai’s new auto plant in Texas?
A plant-specific capacity cannot be stated from the supplied information because verified design flow, TSS, FOG and treatment targets are missing. At HydropureWater’s 4 gpm/ft² typical design point, the published 200 gpm example requires 50 ft²; this is an illustration, not a confirmed Hyundai requirement.
What data is needed to calculate DAF surface area?
Request the 85th-percentile daily flow, short-duration peak profile, TSS, FOG, pH, temperature, existing chemical conditioning and applicable discharge or sewer pre-treatment limit. Also identify batch wash-water, stormwater, nondestructive-test leakage and production-expansion streams so the design basis represents the wastewater reaching the DAF.
How should DAF suppliers be compared during procurement?
Ask every bidder to reproduce the same four-variable calculation from the same influent data: hydraulic loading and area, air-to-solids ratio, effective retention and recycle flow. Verify the recycle pump curve at the calculated gpm. A tank-flow rating without those checks does not establish effective clarification capacity.
When is a standard DAF preferable to custom equipment?
Compare standard catalogue equipment when the calculated duty is within the published 4–300 m³/h range and the influent remains inside its stated contaminant envelope. Above 300 m³/h, compare parallel trains requiring balanced inlet distribution against a custom rectangular tank.
Does meeting a 92–97% TSS-removal target establish regulatory compliance?
No. HydropureWater’s 2026 guide presents 92–97% TSS removal as a target for properly conditioned influent, not a plant-specific result. The final design must be checked against the applicable permit or sewer pre-treatment limits supplied by the owner, with the permitted TSS target, FOG condition and monitoring requirements incorporated into the equipment specification.
Related Equipment
- industrial DAF system — specifications, capacity range, and technical data